Оценок - 4, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
The 12V-trigger uses a 3.5mm mono jack plug, wired as follows: < Sleeve: Ground< Tip: ActiveWhen the C31 is powered-on, the tip carries 12V, current- limited to 30mA; other- wise the tip carries 0V. The remote-in also uses a 3.5mm mono jack plug, wired as above. Remote control signals must be in modulated RC5 format, with a voltage level of 5–15V. Note that the remote receiver will require its own power-supply. Details of the Xantech ‘Dinky Link’ can be found at or ask your dealer. Recording an audio source The C31 allows listening to and recording from the same source, or listening to one source whilst recording another. The signal to be recorded is sent to both the TAPE and VCR output sockets. Selecting the source for recording The recording outputs can be configured in two ways: 1. to allow recording of the source being listened to; 2. to allow recording of a particular (specified) source, regardless of what is being listened to. To record the source being listened to, press the RECORD button 2 repeatedly until the display shows ‘Record source’. After a few seconds the display reverts to showing the volume level, and you are ready to record. In this configuration, selecting a different input changes the source that is routed to the recording outputs. To record one source whilst listening to another, press RECORD again until the display shows ‘Record’ followed by the name of an input (e.g., ‘Aux’, ‘CD’, ‘Tuner’, etc.). Now press the source-selector button on the front-panel for the source you wish to record. Your selection is shown on the display for a few seconds, after which the display reverts to showing the volume level. You are now ready to record. Pressing a different source-selection button changes the source that you are listening to, but does not alter the source that is routed to the recording outputs. Tape-to-tape copying (dubbing) You can perform tape dubbing from VCR to TAPE, but not from TAPE to VCR. For example, to copy from a cassette recorder connected to the VCR socket to a cassette recorder connected to the TAPE socket, first use the RECORD button as explained above and select ‘Record VCR’. This routes the VCR signal to the TAPE output. Listening using headphones The headphone socket bl accepts headphones with an impedance rating between 8. and 2k., fitted with a 6.5mm stereo jack plug. The pre-amp. outputs are muted when headphones are plugged in. The headphone socket is always active, unless the volume has been muted. Product configuration The C31 has a configuration menu that allows various performance and behaviour aspects to be altered. This menu is described in detail on the next page. Buttons have been provided on the front-panel to allow direct access to the most important configuration menu items: 4 BALANCE - gives direct access to the “Balance” menu item. 5 DISPLAY - this changes the display brightness. There are three brightness levels to chose from: ‘on’, ‘dimmed’ and ‘off’. If the C31 is switched off while the display is set to ‘off’, the display will be set to ‘dimmed’ when the C31 is switched on again. 9 REF - this toggles the volume display mode between ‘Standard’, ‘Fine’, and ‘Reference’ (these are described on the next page. When the ‘Reference’ volume display is selected, the light above the Ref button is illuminated. bk TRIM - gives direct access to the “Trim” menu item. Did you know: the original 6.5mm (or 1/4”) head-phone jack, dates from 1878 for use in manual telephone exchanges – making it possibly the oldest electrical connector standard on earth. Source: en.wikipedia.org Amplifier Gain Switch (P1) This switch is to allow the gain of the P1 amplifier to be changed to suit your system requirements. With the switch in, the gain is set to standard ARCAM gain of 31.5dB. This is the normal setting, which allows the P1 to be used in systems where there are other ARCAM power amplifiers (excluding the Arcam P7). With the switch out, the gain is set to ‘THX standard gain’. Use this setting if your P1 is to be used in systems containing amplifiers with THX gain (for example, the Arcam P7). Daisy chaining Both the P35 and the P1 can be connected to further power amplifiers to drive more speakers (e.g., those in other rooms, tri-amplified speakers, etc). This technique is called ‘Daisy chaining’. Connect the AUDIO OUT sockets on the P35/P1 to the pre-amp. input of the next amplifier in series, left to left, right to right. Remote switching By making a connection from the TRIG OUT socket of the C31 pre-amp. to the REMOTE IN socket of your P35/P1, you can use the C31 to switch the power amplifier on and off. If configured in this way, the front panel POWER button of the C31 (or the POWER button on the remote control) switches both amplifiers on and off together. This facility allows you to position your power amplifier in a remote location (such as close to the speaker it is amplifying), yet still control it. The connecting cable to use is a 3.5mm jack lead,...
Эта инструкция также подходит к моделям:Ресиверы и усилители - C31 (1.2 mb)
Ресиверы и усилители - C31 (1.2 mb)
Ресиверы и усилители - P1 (1.2 mb)