Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
100BASE-FX Singlemode Fiber 100BASE-TX Copper C/E-100BTX-FRL -03 P 100BASE-FX 100BASE-TX Fast Ethernet C/100BTX- FRL- 03(SM) Power Illuminated green LED indicates Status LEDs AC power. SDF Signal Detect/Fiber: Steady is connected to device. SDC Signal Detect/Copper: port is connected RXC Receive/Copper: are seen RXF Receive/ seen P E-FX 100BA 100BASE-FX CABLE CONNECTIONS • Be certain that the correct mode and wavelength fiber cable is used for single- mode and/or for multimode fiber cable installations. 100BASE-TX CABLE CONNECTIONS • Be certain that the MDI/MDI-X switch located ON the Slide-In-Module circuit board is set correctly before installing Slide-In-Module in Media Conversion Center. Cable connections between a hub and the media converter require the MDI/MDI-X switch to be set to MDI. Cable connections between the media converter and a terminal, transceiver or NIC require the switch to be set to MDIX. Set switch • Using small flatblade Leave in default position screwdriver or similar tool, MDI-X MDI set MDI/MDI-X switch position position for site installation. toward network connectors toward chassis position ETHERNET CABLE SPECIFICATIONS The physical characteristics of the media cable must meet or exceed IEEE 802.3u 100BASE-TX and 100BASE-FX specifications. 100BASE-TX CABLE SPECIFICATIONS Category 5 wire or better is required. Either shielded twisted pair (STP) or unshielded twisted pair (UTP) can be used. Use a straight-through cable configuration (see back page) . CATEGORY 5: Gauge 24 to 22 AWG Attenuation 20 dB/1000’ @ 10 MHz Impedance 100 . ±10% @ 10 MHz Maximum Cable Distance: 100 meters (330 feet) 100BASE-FX CABLE SPECIFICATIONS SINGLEMODE Fiber-optic Cable Recommended: Fiber-optic Transmitter Power: Fiber-optic Receiver Sensitivity: Wavelength: Bit error rate: Maximum Cable Distance: MULTIMODE Fiber-optic Cable Recommended: Optional: Fiber-optic Transmitter Fiber-optic Receiver Wavelength: Bit error Maximum 9 .m singlemode fiber min: -15.0 dBm max: -8.0 dBm min: -32.5 dBm max: -8.0 dBm 1300nM . 10-9 20 kilometers 62.5 / 125 .m multimode fiber 100 / 140 .m multimode 85 / 125 .m multimode 50 / 125 .m multimode min: -19.0 dBm max: -14.0 dBm min: -32.5 dBm max: -14.0 dBm 1300nM . 10-9 2 kilometers Installing Slide-In-Module(s) C/E- 100BTX-FRL-03 CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing Media Converter Slide-in-Module(s) in the 16-Slot Media Conversion Center. Failure to observe this caution could result in damage to, and subsequent failure of, the Media Converter Slide-in-Module(s). NOTE: Media Converter Slide-in-Modules can be installed in any installation slot, in any order. To install the Media Converter Slide-in-Module in the E-MCC-1600 chassis: 1. Remove Media Converter Slide-in-Module protective plate from selected installation slot by removing two screws that secure plate to front of E-MCC-1600. Retain one installation screw. 2. Carefully slide Media Converter Slide-in-Mod...
Эта инструкция также подходит к моделям:Ресиверы и усилители - C/E-100BTX-FRL-03 (57.72 kb)
Ресиверы и усилители - C/E-100BTX-FRL-03(SM) (57.72 kb)