Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
If necessary, remove the feet from the bottom of the unit. 2. Mount the receiver to one of the bracket’s three mounting plates using two of the supplied 4-40 x 3/16" screws in opposite (diagonal) corners to secure the device to the bracket. It can be vertically mounted facing either up or down (see the illustration below). N On the side mounting plates, the device is typically mounted on the outside of the bracket. On the front mounting plate, the device is typically mounted on the inside of the bracket. ExtronPMK 300Multi-product Projector Mount KitU-Bolt Front MountingPlateSide MountingPlateExtronDVI DL 101EqualizerPower SupplyBracketBrace PMK 300 projector mounting a receiver 3. Strap the power supply to one of the brackets, using the two included tie wraps. N The PMK 300 has a hole in the bottom plate that allows the projector pole to be inserted through the center of the plate, rather than outside of the plate). To install the PMK 300 in this configuration, slide the bracket up from the bottom of the pole before the projector is installed on the pole. U-boltExtronPMK 300Multi-product ProjectorMount KitContouredBracketBaseExtronDVI DL 101EqualizerPower Supply Mounting with the projector pole on the inside 4. Place the contoured bracket brace against the pole and opposite the back plate. The pole should fit snugly into the depression in the center of the bracket brace. 5. Place the U-bolt around the ceiling pole. Insert the two legs of the U-bolt through the round holes on the contoured bracket brace and then through the slotted holes on the bracket’s mounting plate. N The supplied U-bolt fits a typical (1.5" to 2.0" diameter) ceiling pole. 6. Secure the bracket to the U-bolt with the included hex nuts, washers, and lock washers. Tighten the hex nuts just enough that they can be loosened by hand. PMK 350 mounting Mount the DVI DL to a PMK 350 bracket as follows: 1. Remove the front and rear plates from the PMK 350, using an Extron Tweeker or a #2 Philips screwdriver. Retain the screws to reattach the plates when you are finished. 2. If necessary, remove the feet from the bottom of the unit. 3. Secure the DVI DL to one side of the mounting tray, using two of the supplied 4-40 x 3/16” screws in opposite (diagonal) corners. ExtronPMK 350Multi-product ProjectorMounting KitCover SheetFront PlateRear PlateU-boltL-shapedBracketContouredBaseExtronPower SupplyExtronDVI DL 101Equalizer PMK 350 projector mounting a DVI DL 4. Using the two included tie wraps, strap the power supply to the PMK bracket. 5. If desired, remove the back panel of the PMK 350 and mount additional device(s) at the back of the bracket, as described in step 3. 6. Place the PMK 350 around the projector ceiling mounting pole. 7. Assemble the U-bolt and the following parts in the following order (see the illustration below): a. Pass the legs of the U-bolt through the slotted holes on the mount plate flange. b. Place the legs around the projector pole. c. Pass the legs through the holes in the contour base. N The pole fits snugly into the depression in the center of the contoured base. d. Pass the legs through the holes in the L-shaped bracket. N The supplied U-bolt fits a typical (1.5" to 2.0" diameter) ceiling pole. U-boltSlotted Holein PMK TrayL-shapedBracketL-shapedBracket ScrewsContouredBaseCeilingPoleMount PlateFlange Figure 2-8 — Hanging the PMK 350 tray on the projector pole 8. Align the two holes in the bottom of the L-shaped bracket with the two holes in the base of the tray. Secure the L-bracket to the base by inserting two of the provided 6-32 x 5/16" screws through the aligned slots. 9. Move the PMK 350 up to the desired location on the ceiling pole, as close to the ceiling as desired. 10. Secure the L-shaped bracket to the U-bolt using the included hex nuts, washers, and lock washers. Tighten the hex nuts securely. N Be sure to tighten the hex nuts securely enough that the PMK 350 does not slide down the ceiling pole. A socket wrench is recommended to tighten the hex nuts. 11. Secure the front and rear plates to the mounting tray with four of the included #6 screws. 12. If desired, choose one of the provided four sizes of self- adhesive cover sheets, and apply it to the underside of the mounting tray. Front and Back Panel Features and Connections POWER12V 0.2A MAXDVI DL 101DVI-DUAL LINK OUTPUTDVI-DUAL LINK INPUTDVI DL 1013124 DVI DL front and rear panels a Status LED — This dual-color LED lights amber when the DVI DL is receiving power. When a DVI input signal is present, this LED lights green. b DVI input connector — Plug the cable from the input source device into this dual link female DVI-I connector. Dual link rates of up to 2560x1600 @ 60 Hz and single link rates of up to 1920x1200 and 1080p @ 60 Hz are supported. The table on the next page shows the DVI pin configuration. N Dual link DVI cables must be used for dual link DVI signals. If a single link DVI cable is used, only single link DVI signals are possible. PinSignalPinSig...
Эта инструкция также подходит к моделям:Ресиверы и усилители - Dual Length DVI Cable Equalizer DVI DL 101 (1.65 mb)