Make sure that the clock does not fall and become damaged. 3) Remove the two rear screws, separating the two mount halves. 4) Place the handlebar mount halves in the position of your choice on the bars (keep away from curves or areas the bar may not be a consistent thickness), re-insert the supplied screws and tighten gently and evenly (for the mount to tighten properly there should be a small gap between the two halves, no bar is the same so the gap will vary - do not over-tighten ). 5) Loosen

No further manual setting is necessary. SETTING THE STARTING DATE OF DAYLIGHT SAVING TIME Example: Daylight saving time starts on Sunday, March 25, 2001. Year DateMonth D.S.T. START SELECT CHANGE SET SELECT D.S.T. START CHANGE SET SELECT D.S.T. START CHANGE SET 16 SELECT D.S.T. START CHANGE SET Step 1 Press the SELECT button and position the " " mark at the "D.S.T. START". At that moment, the "Year" flashes. (The flashing means it can be changed.) Change the "Year". In case of the example, press

All rights reserved. Contents Here’s all the information you need for setting and operating your new Lathem time recorder. Service information is also included in this manual, in case any problems ever arise. Thank you for choosing a Lathem time recorder. Should you ever need assistance, please let us know. Ordering Accessories ................................................ 2 Setting the Time ........................................................ 3 Changing the Ribbon........................

END SELECT CHANGE SET D.S.T. END SELECT CHANGE SET D.S.T. END SELECT CHANGE SET 22 20 DELETING THE DAYLIGHT SAVING TIME SETTING Press the SELECT button and position the " " mark at the "D.S.T. START". At that moment, the "Year" flashes. (The flashing means it can be changed.) Next, press the SET button. At that moment, the flashing changes from "Year" to "Month". Step 1 D.S.T. START SELECT CHANGE SET D.S.T. START Press the CHANGE button to set at " ". And then press the SET button. At that momen

DO NOT USE IN WET LOCATIONS. THIS TIMER HAS A BUILT-IN RECHARGEABLE BATTERY THAT IS USED TO RETAIN THE CURRENT TIME AND ON/OFF SETTINGS WHEN THE UNIT IS NOT PLUGGED IN AN OUTLET. IN CASE OF A FAILURE OF THE TIMER. PRESS THE RESET BUTTON TO RESTART THE TIMER. TO ACTIVATE YOUR TIMER 1. Display - Remove the plastic film from display. 2. Installation - Plug the timer into a grounded outlet and wait for at least 30 minutes to charge the built-in rechargeable battery. Once the battery has charged, unp

Locate the segments around the outer edge of the timer’s dial. These segments, each representing 15 minutes, can be pushed out and away from the edge of the dial (try using the tip of a pen or pencil). Conversely, segments that have been pushed out can be easily pushed back in by hand. Be sure all segments are pushed in before programming. Select a time period (or periods) you want the appliance turned on, then push out ALL the segments that fall on or within that time period. For example, to ha

Notice ALL segments between 10 PM and 2 AM have been pushed out. Current time is 8:00 PM. CurrentTimeCurrentTimeCurrentTime24 Hour Outdoor Timer Instructions: 1. Locate the segments around the outer edge of the timer’s dial. These segments, each representing 15 minutes, can be pushed out and away from the edge of the dial (try using the tip of a pen or pencil). Conversely, segments that have been pushed out can be easily pushed back in by hand. Be sure all segments are pushed in before programmi

• Do not exceed capacity. • Do not use timer with devices that could have dangerous consequences due to inaccurate timing, such as sun lamps, heaters, etc. • Plug directly into receptacle. NOTICE • No user serviceable parts. Install setup: 1. Plug timer into wall outlet for a 5 minutes to charge internal battery. NOTE: You can unplug the timer to set after initial battery charge. 2. Before programming all settings should be reset. Use a toothpick or pencil to push the “R” button. 3. Select AM/PM

2. Press the HOUR, MINUTE and WEEK buttons as necessary to revise the displayed ON or OFF time and day(s). To remove or restore a setting: 1. Press the PROGRAM button (hold down to scroll) until the display shows the setting you want to remove or restore. 2. Press the RST/RCL button. - If removing, the display will replace the setting with dashes. Pressing the RST/RCL button again will restore the previous setting. To Operate the timer: 1. After setting the timer, plug it in and connect the devi