Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Pattern 1 (displayed as P1) Traditional beep, fast speed, volume and tone control capable Pattern 2 (displayed as P2) Slow speed start that switches to fast speed, lower volume start that gets increasingly louder, volume control capable Pattern 3 (displayed as P3) Various patterns that change, lower volume start that gets increasingly louder, volume control capable Press and hold the Sound Alarm key to activate the sound alarm function. 11 – ENGLISH OPERATION OPERATION - SET THE TIME If your clock is connected to the phone line and you subscribe to Caller ID service, the time will be automatically set when you receive a call. You can also select a 12 or 24 hour mode. Please make sure to set the correct AM/PM time. A round light in the upper right of the clock display will appear for PM time. For AM time, the light does not appear. To select 12 or 24 hour time 1. Press Set Time and the display will show the current time mode (12 or 24). 2. Press Up or Down to change the mode. 3. Press Return to save and exit. To set the time 1. Press Set Time twice and the current hour setting will blink. 2. Press Up or Down to change the hour. Keep pressing the key until you reach the desired hour. 3. Press Set Time and the current minute setting will blink. 4. Press Up or Down to change the minute. Keep pressing the key until you reach the desired minute. 5. Press Return to save and exit. 12 – ENGLISH - SET THE ALARM AND SOUND, VISUAL AND SHAKER NOTIFICATION This clock offers 2 separate alarms that can be set for different times. Alarm 1 is displayed as 1 and Alarm 2 is displayed as 2. When either alarm is switched On, the blue backlighting will appear on the Set Alarm key. The snooze bar will also light red when either alarm is switched On. If neither alarm is turned On, the snooze bar will not be lit. Note: You must activate the alarm notification modes that you wish to use. See Alarm Notification Modes and Activation on pages 9-11. To set your alarm 1. Press Set Alarm and “1” will be blinking on the left side of the display. 2. Press Up or Down to select the alarm (alarm 1 or alarm 2) you want to set and then press Set Alarm . 3. The current On/Off status for that alarm will blink. Press Up or Down to select On or Off and then press Set Alarm . 4. The current alarm hour will blink. Press Up or Down to change the hour and then Press Set Alarm . 5. The current alarm minute will blink. Press Up or Down to change the minute and then Press Set Alarm . 13 – ENGLISH 6. The current On/Off selection for the Sound Alarm (r1=On/Off) will blink. Press Up or Down to select On or Off and then Press Set Alarm . 7. If you select On, the current pattern for the sound alarm (P1-P3) will blink (if selecting Off, skip to step 8). Press Up or Down to select the desired sound pattern and then Press Set Alarm . 8. The current On/Off selection for the LED/Lamp Flashing (F1=On/Off) will blink. Press Up or Down to select On or Off and then Press Set Alarm . The alarm setting is now complete and will show the current time. Please Note: At any point, you can press Return to save and exit. - SNOOZE KEY When your clock alarm activates, you can temporarily turn it off using the Snooze key. The Snooze key will stop the alarm for 5 minutes. After 5 minutes, the alarm will activate again. You can continue to press the Snooze key for a total of 1 hour after which the alarm mode will be automatically switched off. The Snooze key is located on the top of the clock. - ALARM OFF KEY When your clock alarm activates, it will continue minutes if no key is pressed. If you press Set Alarm for 5 , the alarm will turn off and it will reset to activate at the same time the next day. 14 – ENGLISH - TELEPHONE RING SIGNALER If you choose to connect the Shake Up Wake Up to your telephone line, it will notify you when there is an incoming phone call. The sound ring selection is controlled by a separate switch located on the back of the clock. You must activate the Sound Alarm key to activate the telephone sound ringer. Additionally, any notifications that you have activated (LED flasher/lamp and shaker) for alarm clock notification will also alert you to the telephone ringing. 2 31 1. Connect one end of the included telephone cord to the LINE IN jack on the clock and connect the other end of the cord to the phone jack in the wall. 2. Make sure the AC power plug is connected to a standard AC wall outlet or surge protector. 3. Select Ring Tone 1-3 located on the back of the clock. 4. Be sure the notifications that you desire for telephone ring signaling (sound alarm, LED flasher/lamp, shaker) are activated. 5. Optional: Connect your telephone to the LINE OUT jack. This will allow you to use that telephone from the clock location. When the clock alerts you to an incoming call, simply answer any phone and the alarm will stop. After you hang up, your clock is ready to alert the next call. 15 – ENGLISH TECHNICAL SPECIFICATIONS General Number: SW200 Amplification: Up to 87 dB F...