MASK ANY AREA YOU DO NOT WISH TO SPRAY. Once you have set up ready to spray, switch on the unit. No paint will be sprayed from the gun until the trigger on the spray gun is pulled. Before starting any work on spraying actual objects we suggest you spend a small amount of time practicing on cardboard or newspaper until you have got used to how the gun works. 11 SPRAY PATTERNS Fig.2 Vertical Jet Round JetHorizontal Jet The gun has 3 different spray patterns – Horizontal, Vertical and Round (Fig.2)

BEFORE USE – PLEASE READ THE MANUAL AND SAFETY INSTRUCTIONS. Please retain for future reference MODE D’EMPLOI Merci d’avoir choisi le systeme professionnel de pulverisation de peinture basse pression Earlex. Cet appareil est dote du systeme HVLP (haut volume d’air, basse pression de peinture) extremement polyvalent dont vous pourrez vous servir pour une grande variete d’applications. AVANTTOUTE UTILISATION,VEUILLEZ LIRE CE MANUEL ET LES INSTRUCTIONS RELATIVES A LA SECURITE. Veuillez conserver ce

• We recommend you wear protective clothing. • Stir the paint well using a mixer where possible. • Make sure there are no solid particles in the paint. • Many products can be sprayed without being thinned. However, if the application is not good, thin the product progressively in stages of 5%. • Most paints can be sprayed by being thinned just a little, e.g. by 5% or 10%. • Some thick paints such as outer wall paints and certain undercoats will need to be thinned by 20% or 25%. • Use water to th

Please retain for future reference. 2 EXPLODED PARTS VIEW 13 14 14 13 Fig.2 12 11 10 9 7 8 4 5 6 2 3 1 A B Fig.1 Fig.3 HV3500 HV2900/ 3900 PARTS LIST FFiigg..11 No.Description Part Code No.Description Part Code 1. Needle and Fluid Tip Tool V0018 7. Fluid Needle 2.0mm V0006 2. Air Cap Ring V0001 8. Lip Seal -Fluid Needle V0007 3. Air Cap V0002 9. Paint Flow Adjuster V0011 4. Spray Direction Plate V0003 10. Paint Container Seal L0682 5. Fluid Tip 2.0mm V0004 11. Pick-up Tube V0012 6. Fluid Tip O-R

2) When you get to the end of the line, release the Trigger for a moment and then apply the product in the opposite direction just beneath the line you have sprayed. 3) Next, to achieve a vertical strip adjust the Spray Direction Plate (4) to the horizontal position then pull the Trigger and move your arm up and down over the horizontal strips you just have sprayed. Through gradual movement of the Spray Direction Plate (4) between Horizontal, Vertical and Round spray pattern you can vary the wid

Please retain for future reference. MODE D’EMPLOI AVANT UTILISATION, MERCI DE LIRE ATTENTIVEMENT LE MODE D'EMPLOI ET LES CONSIGNES DE SECURITE. Veuillez conserver cette notice pour toute consultation future. MANUAL DE INSTRUCCIONES ANTES DE UTILIZARLA -POR FAVOR LEA EL MANUAL PRINCIPAL Y LAS INSTRUCCIONES DE SEGURIDAD. Guardelo para futuras consultas. DO NOT RETURN TO STORE IF THIS PRODUCT HAS BEEN USED If you have any questions relating to this product please contact Earlex customer service TOL

The spray applicator should be thoroughly cleaned after each use. Follow the cleaning instructions on page 9 with reference to the drawings on page 3 ! Check the needle and fluid tip on a regular basis for excessive wear, and replace as necessary. See the cleaning instructions for the correct procedure for removing these parts. Replacement needle sets are available from Earlex Ltd. ! Keep all moving parts lubricated with a light smear of petroleum jelly. ! Lubricate the gland washer, after each

BEFORE USE - PLEASE READ THE SAFETY & OPERATING INSTRUCTIONS. Please retain for future reference N0150 05/05.qxd 27/5/05 10:28 am Page 2 SAFETY INSTRUCTIONS WARNING! FIRE AND EXPLOSION HAZARD. . CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, USE INDOORS ONLY. . The substances used with this spray applicator (paint, thinners etc) may contain hazardous, harmful, explosive or corrosive materials. ALWAYS COMPLY WITH THE SAFETY INSTRUCTIONS ISSUED WITH THIS PRODUCT AND THE MATERIAL BEING US

The round spray is used for small objects or for areas - such as corners – that are difficult to reach. To adjust the spray pattern, loosen the Air Cap Ring (1), adjust the position of the Air Cap (2) to obtain either a vertical, horizontal or round pattern then re-tighten the aircap ring. PAINT VOLUME The volume of paint sprayed is easily adjustable. (Fig.5(a)) Completely close Fluid Adjusting Screw (8) by turning this clockwise as far as it will go. Whilst pulling the trigger, begin turning th

2. Pour any residual material into its container so that it can be used for the future. 3. Pour a quantity of the respective thinner into Container, shake the gun lightly, reassemble the gun, then spray this liquid through the gun. Repeat this until the thinner being sprayed is coming through with no traces of paint. 4. Clean any traces of paint off the outside of the gun. 5. Clean the Paint Container Seal (12) inside the gun body. 7 L0553 (04-08) (US-FR-ES).qxd 20/6/08 2:25 pm Page 8 L0553 (04-