Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 17. Avoid Lead-based paints. Before beginning any paint removal process, determine whether the paint contains lead. This can be done by the local health department or paint professional using a paint analyzer to check the lead content of the paint to be removed. Lead-based paint should only be removed by a professional and should not be removed by using a heat gun. 18. Clean sprayer with care. Use nonflammable solvents. Avoid solvents that can be forcibly ejected from the sprayer nozzle and air passages. 19. Do not spray near open flames, pilot lights, stoves, heaters, or any other heat source. Most solvents and coatings are highly flammable, particularly when spraying. The work area must always have adequate ventilation. 20. Do not smoke while spraying. Most solvents and coatings are highly flammable, especially when spraying. SKU 43430 Page 3 21. Read all information concerning coating products and cleaning solvents. Chlorinated solvents (e.g., 1-1-1 Trichlorethylene and Methylene Chloride, also known as methyl chloride) can chemically react with aluminum and may explode. Many paint sprayers contain aluminum. If you have any doubt about potential chemical reactions, contact the solvent or coating manufacturer. 22. Materials used when painting or cleaning may be harmful or fatal if inhaled or swallowed. Use only in an area with adequate ventilation. Use a respirator or mask when painting or using cleaning solvents (see number 9 of this list). 23. Never release the sprayer lid while the cup is pressurized. The paint could burst out and contaminate your body. 24. Be aware of other people and animals. Do not use the sprayer near children or animals. Keep all visitors away from the work area. Do not let children or visitors handle tools. 25. Industrial applications must follow OSHA requirements. 26. Be aware of air hoses and their connections. Do not trip over hoses. Make sure all connections are tight. 27. Maintenance. For your safety, maintenance should be performed regularily by a qualified technician. Warning:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Warning: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.) Unpacking When unpacking, check to make sure that all the parts are included. (See the Parts List and Assembly Drawing at the end of this manual.) If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Assembly During the following procedure, refer to the Assembly Drawing on page 10. 1. Before operation, check all sprayer seals before connecting to the air supply. 2. Insert the Material Sleeve (8) into the Cup Connector (25). 3. Attach and fully secure the Plastic Cup (9) to the Cup Connector (25). 4. Attach and fully secure the Air Regulator (16) to the Gun Body (26) handle Air Connector (7). REV 01/07 SKU 43430 Page 4 5. Connect an air hose to the air compressor air outlet. 6. While holding the open end of the air supply hose, momentarily turn on the compressor air to clean out any debris within the hose. 7. Connect the air supply hose to the Air Regulator on the Sprayer and secure. 8. Tighten the Fluid Nozzle (18) using the Spanner Wrench (12). 9. Clean the sprayer out by flushing with a nonflammable solvent. Operation Filling and Adjusting the Air Spray Gun 1. Remove the Plastic Cup Cover (10) and fill the Plastic Cup with the material to be sprayed. 2. Replace and tighten the Cup Cover. 3. Prepare a spraying test area. 4. Turn on the air supply and adjust the Air Regulator (16) on the Gun Body to between 15 and 50 PSI. 5. Point the Air Nozzle in the direction of the spray test area and press the Trigger (4). 6. Adjust the spray pattern (horizontal or vertical) by turning the Nozzle (17). 7. Adjust the air-to-material mixture by adjusting the Air Adjusting Valve (15). 8. Adjust the spray width using the Fluid Control Knob (2). Do not unscrew completely. Paint and Materials Preparation Verify with the paint or materials supplier the percentage of thinning required for use with a High Volume-Low Pressure (HVLP) Sprayer. Try thinning a small amount and testing the spray action. Thoroughly mix material before testing. Rev 04/01 SKU 43430 Page 5 Rev 10/00 Viscosity Viscosity is the technical term used to indicate the liquidity (thickness or thinness) of the material to be sprayed. Viscosity is measured in the number of seconds required for the material to pass thro...
Эта инструкция также подходит к моделям:Распылители краски - 43430 (244.54 kb)