Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Use the handset near the base unit. Lift the handset off the base unit and press SEARCH © or @ to enter the list. O Press SEARCH @or (A) repeatedly to find ^ the caller you want to store in memory. • If the number requires editing, see page 29. 2 Press (AUTO). 4 Press a memory station number (® to ®). • A beep sounds. • The display will return to step 2. You can continue storing other items. To return to the stand-by mode, press (EXIT) or wait for 60 seconds. • To cancel during programming, press (EXIT). Start again from step 1. • If 3 beeps sound and the display shows “out of range”, move closer to the base unit and try again. If “out of range” is still displayed, place the handset on the base unit. Start again from step 1. • You cannot store caller information in the Speed Dialer memory if a phone number is not displayed. 10 new calls v=New A=old CINDY TURNER 1-234-456-7890 11:20A JAN12 x3 Save in AUTO Select 0-9 1-234-456-7890 Save in AUTO 0 30 Erasing the Caller List Information After checking the Caller List, you can erase some or all of the entries. The TALK indicator light must be off. Use the handset near the base unit. To erase a specific caller from the Caller List ILift the handset off the base unit and press SEARCH 0or (a) to enter the list. 2 Press SEARCH 0or (a) repeatedly to find the caller you want to erase from the Caller List. 10 new calls v=New A=Old TOM REAGAN 444-5555 12 : 2 0A JAN12 ^ Press 1 CLEAR 1. • A beep sounds and the information is erased. © After a few seconds, the display will show the previous caller information. • To return to the stand-by mode, press (EXIT] or wait for 60 seconds. Clear To erase all entries in the Caller List 1 Lift the handset off the base unit and press SEARCH 0 or (a) to enter the list. Press fCLEAR). Press [CLEAR] again. • A beep sounds and all entries are erased. • The handset will return to the stand-by mode. Make sure this display is shown. 0 new call v=New A=old Press CLEAR for all clear All clear • If 3 beeps sound and the display shows “out of range”, move closer to the base unit and try again. If “Out of range” is still displayed, place the handset on the base unit. Start again from step 1. 31 Voice MaiB Service Voice mail service is an electronic on-line answering system offered by your telephone company. After subscribing, the voice mail system will answer calls automatically when your line is busy or if calls are not answered. Callers can leave messages by following the pre-recorded instructions. When voice mail messages are recorded, the VOICE MAIL indicator will flash. You can access the voice mail system quickly by pressing (VOICE MAIL). To use this feature, you must first store your access number. Storing a Voice Mail Access Number The TALK indicator light must be off before programming. Use the handset near the base unit. ■j Press (PROGRAM). • The TALK indicator flashes. p Press SEARCH 0 (Next key) repeatedly ^ until “Save mailbox# ?” is displayed. 2 Press SEARCH @(Yes key). ^ Enter your access number up to 32 digits. • If you enter a wrong number, press (CLEAR). Digits are erased from the right. g Press (VOICE MAIL) (Save key). • A beep sounds. Save AUTO# ? v=Next A=Yes Save mailbox# ? v=Next A=Yes Enter mailbox# 1234567890 VOICEMAIL=Save 1234567890 Save mailbox# • To cancel during programming, press (EXIT) or (PROGRAM). Start again from step 1. • If 3 beeps sound and the display shows “Out of range”, move closer to the base unit and try again. If “Out of range” is still displayed, place the handset on the base unit. Start again from step 1. To erase a stored number Press (PROGRAM) SEARCH 0 (Next key) twice *+ SEARCH 0 (Yes key) * (CLEAR) (VOICE MAIL) (Clear key). 32 E^> Setting the Voice Mail Tone If your voice mail service sends a voice mail tone after a new message has finished recording, set to “On”. The VOICE MAIL indicator will flash when a message is recorded in your mailbox. You will hear a series of voice mail tones then a dial tone after pressing [TALK], (Contact your service provider about your service.) Set to “Off’ if: — you do not subscribe to a voice mail service, — your voice mail service does not send a voice mail tone, or — the unit is connected to a PBX. Your phone comes from the factory set to “On”. The TALK indicator light must be off before programming. Use the handset near the base unit. 1 Press [PROGRAM]. • The TALK indicator flashes. p Press SEARCH 0 (Next key) repeatedly ^ until “Voicemail tone?” is displayed. Press SEARCH @ (Y es key). 4 To select “Off’, press SEARCH 0. OR To select “On”, press SEARCH 0 . • A beep sounds. Save AUTO# ? v=Next A=Yes Voicemail tone? v=Next A-Yes Voicemail tone v=On a=0 f f Voicemail tone Off Voicemail tone On • To cancel during programming, press [EXIT) or (PROGRAM). Start again from step 1. • If 3 beeps sound and the display shows “Out of range”, move closer to the base unit and try again...