Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
6 TIME Press to open the Timer menu. 7 MENU Press to open the on-screendisplay (OSD). 8 CH+ Press to change to a channel witha higher number. 9 VOL– Press to decrease the volume. 10 CH – Press to change to a channel witha lower number. 11 CCD Press to select the closed captionmode. 12 SLEEP Press to set the sleep timer. 13 INPUT Press to select the video inputmode. 14 PICTURE Press to select a presetbrightness setting. 15 MUTE Press to mute the sound. Press again to restore the sound. 16 VOL+ Press to increase the volume. 17 SCAN Press to memorize channels. Insignia NS-F20C 20" Flat Tube TV Installingremote control batteries Warning Do not throw the batteries into fire. Dispose of used batteries as hazardous waste. Caution Do not drop or disassemble the remote control. Do not get the remote control wet. To install batteries in the remote control: 1 Remove the battery cover. 2 Insert two AAA batteries into the battery compartment. Make sure that the + and – symbols on the batteries match the + and – marks inside the battery compartment. 3 Replace the battery cover. Note When the remote control will not be used for a long period of time or when the batteries are worn out, remove the batteries to prevent leakage. Setting up your TV Connecting an antenna or direct cable VHF UHF Mixer (not included) Antenna jack Power cord To connect an antenna or direct cable: 1 Plug one end of a coaxial cable into your antenna or cable wall jack. 2 Plug the other end of the cable into the antenna jack on the back of your TV. Connecting a cable or satellite receiver To connect a cable converter box or satellite receiver: 1 Connect a coaxial cable from your cable or satellite signal source to the IN jack on cable converter box or satellite receiver. 2 Plug a coaxial cable into the OUT jack on your cable converter box or satellite receiver, then plug the other end of the cable into the antenna jack on the back of your TV. Connecting a standard A/V device Your TV has two set of standard A/V jacks. One set is on the back of your TV. The other set is on the left side of your TV. To connect a standard A/V device to the back A/V jacks: 12345678 No. Component 1 DVD player 2 VCR 3 AUDIO R OUT 4 AUDIO L OUT 5 VIDEO OUT 6 VIDEO2 IN 7 AUDIO L IN 8 AUDIO R IN 1 Plug the video (yellow) connector on a standard A/V cable into the video out jack on the external device, then connect the other video (yellow) connector into the VIDEO IN jack on the back of your TV. 2 Plug the left audio (white) connector on a standard A/V cable into the left audio out jack on the external device, then connect the other left audio (white) connector into the AUDIO IN L (left) jack on the back of your TV. 3 Plug the right audio (red) connector on a standard A/V cable into the right audio jack on the external device, then connect the other right audio (red) connector into the AUDIO IN R (right) jack on the back of your TV. Insignia NS-F20C 20" Flat Tube TV To connect a standard A/V device to the side A/V jacks: No. Jack 1 DVD player 2 VCR 3 VIDEO 4 AUDIO L 5 AUDIO R 1 Plug the video (yellow) connector on a standard A/V cable into the video out jack on the external device, then connect the other video (yellow) connector into the VIDEO jack on the side of your TV. 2 Plug the left audio (white) connector on a standard A/V cable into the left audio out jack on the external device, then connect the other left audio (white) connector into the AUDIO L (left) jack on the side of your TV. 3 Plug the right audio (red) connector on a standard A/V cable into the right audio jack on the external device, then connect the other right audio (red) connector into the AUDIO R (right) side on the back of your TV. Connecting a component video device To connect a component video device: 1 Plug the Y (green) connector on a component video cable into the Y out jack on the external video device, then plug the other Y (green) connector into the Y IN jack on the back of your TV. 2 Plug the Cb (blue) connector on a component video cable in the Cb out jack on the external video device, then plug the other Cb (blue) connector into the Cb IN jack on the back of your TV. 3 Plug the Cr (red) connector on a component video cable into the Cr out jack on the external video device, then plug the other Cr (red) connector into the Cr In jack on the back of your TV. 4 Plug the left audio (white) connector on a standard A/V cable into the left audio out jack on the external device, then connect the other left audio (white) connector into the AUDIO IN L (left) jack on the back of your TV. 5 Plug the right audio (red) connector on a standard A/V cable into the right audio jack on the external device, then connect the other right audio (red) connector into the AUDIO IN R (right) jack on the back of your TV. Connecting an S-Video device To connect an S-Video device: 1 Plug one end of an S-Video cable into the S-Video out jack on the external device, then plug t...