Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Conventional channel/trunking ID can be programmed up to 512. FleetSync'B is a trademark of Kenwood Corporation. LTR• is a registered trademark of Transcrypt International. Applicable MIL-STD & IP Selectivity Wide: Narrow: 84dB (±30kHz) 80dB (±25kHz) 76dB (±15kHz), 73dB(±12.5kHz) 76dB (± 12.5kHz) Intermodulation Wide: 77dB (±30, 60kHz) 79dB (±25, 50kHz) Narrow: 75dB (±15, 30kHz) 73dB (±12.5, 25kHz) Spurious Response 85dB Audio Output External: 12W (@ 4 Q 3% distortion) 13W (@ 4 Q 5% distortion) Internal: 3.2W (@ 16Q3% distortion) 3.5W (@ 16 Q 5% distortion) TRANSMITTER (Measurements made per EIA/TIA-603) RF Output Power 50 to 15 watts 45 to 15 watts High: 50 watts 45 watts Low: 15 watts 15 watts Type of Emission Wide: 16K0F3E, 20K0F1D Narrow: 11K0F3E, 11K2F1D Spurious Response 75dB FM Hum & Noise Wide: 48dB Narrow: 42dB Microphone Impedance 600 Q Audio Distortion Less than 1 % at 1000Hz Kenwood follows a policy of continuous advancement in development. For this reason specifications may be changed without notice. Standard MIL 810C Methods/Procedures MIL 810D Methods/Procedures MIL 810E Methods/Procedures MIL 810F Methods/Procedures Low Pressure 500.1/Procedure I 500.2/Procedure I, II 500.3/Procedure I, II 500.4/Procedure I, II High Temperature 501.1 /Procedure I, II 501.2/Procedure I, II Cat. A1 501 3/Procedure I. II Cat. A1 501 4/Procedure I, II Low Temperature 502.1/Procedure I 502.2/Procedure I, II Cat. C1 502.3/Procedure I, II Cat. C1 502.4/Procedure I, II Temperature Shock 503.1/Procedure I 503.2/Procedure I Cat. A1.C1 503.3/Procedure I Cat. A1, C1 503.4/Procedure I, II Solar Radiation 505.1 /Procedure I 505.2/Procedure I 505.3/Procedure I 505.4/Procedure I Rain 506.1/Procedure II 506.2/Procedure I 506.3/Procedure II 506.4/Procedure III Humidity 507.1/Procedure II 507.2/Procedure I 507.3/Procedure II 507.4 Salt Fog 509.1/Procedure I 509.2/Procedure I 509.3/Procedure I 509.4 Dust 510.1/Procedure I 510.2/Procedure I 510.3/Procedure I 510.4/Procedure I, III Vibration 514.2/Procedure VIII, X 514.3/Procedure I Cat. 8 514.4/Procedure I Cat. 8 514.5/Procedure I Cat. 20 Shock 516.2/Procedure I, II, III, V 516.3/Procedure I, IV, V 516.4/Procedure I, IV, V 516.5/Procedure I, IV, V footnotes from Front: ' KRK-9, KCT-22M/M2/M3, KCT-23M/M3 remote control options required. 2 6-Pin Accessory Connector for external speaker, PA Output & ignition sense input. 3 KCT-18 ignition sense cable option required; plugs into mobile 6-pin jack ignition sense input. 4 Built-in PA/HA outputs (no option board required); Horn Alert operates for 2-Tone or DTMF selective call decode only. 5 Short Text Messages are radio stored & LCD displayed; Long Text Messages require a KDS-100 and KCT-40. 6 FleetSyncf GPS features require an internal GPS board or externally wired GPS receiver with NMEA TTL level serial data output to the internal COM 1 or 2 set to ''GPS". KENWOOD 20809 Kensington Blvd Lakeville,MN 55044 -C ApVANÙb WIRELESS COM M UN I C^n O N 5 .......... 877-202-5060 www.advancedwireless.com...
Эта инструкция также подходит к моделям:Радиоприемники - VHF/UHF FM Mobile Radios TK-7150 (1.84 mb)