Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
To program the second group of 10 preset channels (upper group) press andHold the Shift (SFT) button for 2 seconds until a tone is heard. By doing thisyou have entered the second bank (upper group) and the SCU is ready toaccept an additional group of 10 channels into memory. 5. Select the desired channel you wish to save in memory by using thedirectional buttons (•• ....................), direct access method, or category select tuningmethod. 6. With the desired channel displayed, press and hold any one of the numberedkeypad buttons for until the confirmation tone (or second tone) is heard. Continue with this process until the second group of 10 preset channels isloaded (upper group). Preset channels being previewed are displayed in the lower right corner. A black number on white background indicates that it is part of the upper group of channels and a White number on a Black background indicates that it is part of the lower group. SPECIAL FUNCTIONS USING THE SHIFT BUTTON There are a number of user preference functions that can be adjusted simply by using the Shift (SFT) button with a specific number code. These functions are explained in the following paragraphs. In general, a shift/code is entered in the following manner: SFT 0 9 , where: (SFT) represents Shift button activation and XX represents the specific function code. (The 4-digit code always starts with 09.) SFT DIRECT FM FREQUENCY SELECTION The selection of a specific FM frequency can be directly accessed using the appropriate code; these codes are presented as follows: 8 CODE CTIONSELE 21 88.1MHz 22 88.3MHz 23 88.5MHz 24 88.7MHz CODE SELECTION 25 88.9MHz 26 89.1MHz 27 89.3MHz 28 FM MUTE Figure 10. Modulator Frequency Codes NOTE: The default frequency is 88.5MHz SYSTEM DEFAULT SHIFT CODE Defaults refer to the settings that are entered at the factory. When code 31 is entered, the system is reset to the following defaults: 1. All channel presets cancel and revert to channel 184. 2. The LCD backlighting reverts to Green 3. Button confirmation tone is turned on. 4. All channels that were previously Skipped are reinstated. 5. Previously Locked Out Channels are released by entering (SFT)+0994+(SFT). LCD CONTRAST SHIFT CODE To change the LCD contrast: 1. Enter code 35. 2. Use the Up and Down directional buttons to increase or decrease display contrast, respectively. 3. Press the SFT button to exit LCD contrast mode. 128-6374A 8 of 12 LCDBACKLIGHTDIMMINGSHIFTCODE PARENTALCONTROLCODES To enable the LCD backlight dimming feature: 1. Enter shift code 36, “DIMMING ADJUST” will be displayed. 2. Use the Up and Down directional buttons to increase or decrease display dimming, respectively. 3. Press the (SFT) button to exit LCD backlight dimming mode. BUTTON CONFIRMATION TONE SHIFT CODE Normally, a beep confirmation tone is heard each time a button is pressed . on the SCU. To silence this confirmation tone: 1. Enter code 40. 2. To turn the beep tone on again, enter code 41. LCD BACKLIGHT COLOR SHIFT CODES The backlight color for the LCD display can be either Green or Amber; toselect the desired color, enter one of the following codes: 1. Green-51 2. Amber-52 SCAN SET SHIFT CODES To invoke the Scanning mode of Normal Preset or Normal Non-Preset channels: 1. Normal Channel Scan-60 “ENTER CHANNEL TUNE” will be displayed: Operation in normal mode, whereby channels can be scanned in sequentialorder, up or down. 2. Preset Channel Scan-61 “ENTER PRESET CHANNEL TUNE” will be displayed: Operation in this mode makes channel scanning possible onlywithin the same category or group. CHANNEL/CATEGORY SELECTION SHIFT CODES To invoke the Channel(Normal)/Category selection mode: 1. Normal (Default Mode)-80: Operation in normal mode, whereby channels can be selected in sequential order, up or down. “SIRIUS” Will be displayed in the lower portion of the LCD Screen. 2. Category-81: Operation in this mode makes channel changingpossible only within the same category or group. CHANNEL SKIP SHIFT CODE If you wish to prevent acquisition of a particular channel during the channel selection process: 1. Recover Skipped Channels-90: Regain access to the channel by usingthe direct selection method to select the skipped channel; then enter code 90. (SFT+0990+SFT) NOTE: This function can only be selected when directly accessing the channel(s) to be skipped. 2. Skip Channel-91: The channel will be skipped over during channel selection. (SFT+0991+SFT) 9 1. Current Channel Parental Lock Out----92: Lock Out the current channel so that it may only be accessed with a chosen password. (SFT+0992+SFT) NOTE: This function can only be selected when directly accessing the channel(s) to be locked out. 2. Parental Lock Out Security Code Change----93: This code allows the user to change the Lock Out Security Code . (SFT+0993+SFT) 3. Release Parental Lock Out----94: This code is used to Release the current Locked channel. (SFT+0994+SFT) 4. Initialize Security Code ----98: This code is used to set and use a sec...
Эта инструкция также подходит к моделям:Радиоприемники - SRSIR-001, SRSIR-001FM, SRSIR-001FMR (1.09 mb)