Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Accessing Channels SELECTING CHANNEL CATEGORIES (only in Category Mode) This section describes the procedure used to select a specific group or category of entertainment. Entering into category mode can be accomplished either by Pressing (SFT)+0981+(SFT) or to quickly shift between Category mode and Channel mode, momentarily Press and release (SFT) then Press and Hold (SFT) for 2 seconds, “ENTER CATEGORY TUNE” or “ENTER CHANNEL TUNE” will be displayed . 1. With the system powered up, momentarily press the Shift (SFT) button causing the first channel number in the current category to flash for 5 seconds. 2. While the number is flashing, momentarily press and release either directional button (•• ....................) a desired category is reached. The category will advance one at a time and will also flash for 5 seconds. If no further advance is made, the flashing will stop and the category will then remain steady. 3. To advance rapidly in the chosen direction (Up or Down) and while the channel number is flashing, momentarily press and release either directional button (•• ....................) in a rapid manner. Release the directional button when a desired channel is reached. PRESS UP BUTTON TO ADVANCE TO NEXT HIGHER CATEGORY CATEGORY/ CATEGORY/ PRESS PRESS DOWN BUTTON TO GROUP NUMBER GROUP SHIFT ADVANCE TO NEXT FLASHES LOWER CATEGORY Figure 8. Selecting Channel Categories The channel tuning will automatically wrap around from the last to the firstchannel in that category or vice-versa. When a new category is chosen, theradio will automatically select the first channel in that category. NOTE: If a directional button is Pressed and Held channels will begin to scrollin numerical sequence through all categories until the button is released. This navigation mode will continue to function in the same manner in the newcategory. The user must exit this mode before attempting to perform any otherfunction. To exit this mode, enter Shift (SFT) 0980 Shift (SFT). PRESETTING DESIRED CHANNELS This section describes how to preset up to 20 channels on your SCU(two groups of 10 channels, upper and lower) for rapid and easy access. Proceed as follows: 1. Select the desired channel you wish to save in memory by using thedirectional buttons (•• ....................), direct access method, or category select tuningmethod. 2. With the desired channel displayed, press and hold any one of the numberedkeypad buttons until the confirmation tone (or second tone) is heard(Refer to Confirmation Tone(s) Function). Continue with this process untilthe first group of 10 preset channels is loaded (lower group). NOTE: There is a preset channel group indicator icon located in the top right corner of the SCU display. This is used to determine which group you are in. ·(SR1) = Lower Preset Channel Group (first 10 channels) ·(SR2) = Upper Preset Channel Group (next 10 channels) 3. Repeat the procedure in steps 1 and 2 to save nine other desirable channels for quick access. PRESS AND HOLD ANY NUMBER BUTTON CH 4 (0-9) TO COMMIT THECHANNEL TO PRESET MEMORY SELECT THE THE PRESET MEMORY LOCADESIRED CHANNEL TION APPEARS HERE Figure 9. Setting Preset Channels 7 128-6374A 7 of 12 Each category or group is assigned a sequential block of channels. To navigate within a category, enter Shift (SFT) 0981 Shift (SFT). This mode will allow the user to switch between channels within a chosen category.C 4. To program the second group of 10 preset channels (upper group) press andHold the Shift (SFT) button for 2 seconds until a tone is heard. By doing thisyou have entered the second bank (upper group) and the SCU is ready toaccept an additional group of 10 channels into memory. 5. Select the desired channel you wish to save in memory by using thedirectional buttons (•• ....................), direct access method, or category select tuningmethod. 6. With the desired channel displayed, press and hold any one of the numberedkeypad buttons for until the confirmation tone (or second tone) is heard. Continue with this process until the second group of 10 preset channels isloaded (upper group). Preset channels being previewed are displayed in the lower right corner. A black number on white background indicates that it is part of the upper group of channels and a White number on a Black background indicates that it is part of the lower group. SPECIAL FUNCTIONS USING THE SHIFT BUTTON There are a number of user preference functions that can be adjusted simply by using the Shift (SFT) button with a specific number code. These functions are explained in the following paragraphs. In general, a shift/code is entered in the following manner: SFT 0 9 , where: (SFT) represents Shift button activation and XX represents the specific function code. (The 4-digit code always starts with 09.) SFT DIRECT FM FREQUENCY SELECTION The selection of a specific FM frequency can be directly accessed using the appropriate code; these codes are presented as follows: 8 CODE CTIONSELE 21 88.1MHz 22 ...
Эта инструкция также подходит к моделям:Радиоприемники - SRSIR-001 (1.09 mb)