Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
The National Oceanic and Atmospheric Administration (NOAA) provides continuous, around-theclock broadcasts of the latest weather information. Taped weather messages run every four (4) to six (6) minutes and are revised every two (2) or three (3) hours, or as needed. The Coast Guard also announces weather and other safety warnings on Channel 16 and DSC Channel 70. Smart boaters keep an eye on safety and an ear to the radio — and never let the weather catch them unaware. NOAA Emergency Weather Alert In the event of a major storm or other weather condition requiring vessels at sea or on other bodies of water to be notified, NOAA broadcasts a 1050 Hz tone that receivers such as your CobraMarine™ VHF radio can detect and warn you of a weather alert condition. When the Weather Alert mode on your radio is On, this signal will produce the weather alert alarm tone from the speaker and a “weather alert” message on the LCD to signal that a weather alert is being broadcast. The radio will automatically switch to Weather Radio mode. Test To test this system, NOAA broadcasts the 1050 Hz signal every Wednesday sometime between 11 a.m. and 1 p.m. in each local time zone. Any receiver that can detect the weather alert tone may use this feature to verify that this feature is functioning properly. Weather Frequency 162.550 162.400 162.475 162.425 162.450 162.500 162.525 161.650 161.775 163.275 Channel RX Frequency MHz 1 2 3 4 5 6 7 8 9 10 24 English Nothing comes close to a Cobra® 25 Nothing comes close to a Cobra® Mounting AndPowering The Radio 27 IntroOperationCustomerAssistanceWarrantyNoticeSecondary And Start-Up Mounting And Powering The Radio • Before using your CobraMarine™ VHF radio, it must be installed on your vessel. Installing Your Radio Choose a location for your radio where it will be conveniently accessible with the following factors in mind: n The leads to the battery and the antenna are best kept as short as possible. n The antenna must be mounted at least three (3) feet from the transceiver. n The radio and all speakers need to be far enough from any magnetic compass to avoid deviation due to the speaker magnet. n There needs to be free air flow around the heat-sink fins on the back of the transceiver. Surface Mount A Surface Mounting kit is included with your CobraMarine™ VHF radio to allow its installation on almost any flat surface. To Mount The Transceiver On Almost Any Flat Surface: 1. Use the mounting bracket as a template to drill holes for the mounting screws. 2. Attach the mounting bracket to the chosen surface. 3. Attach the transceiver to the mounting bracket with the locking knobs. 4. Tilt the transceiver to a convenient angle and tighten the locking knobs. Surface Mounting Kit Tilt Lock Knobs IntroOperationCustomerAssistanceWarrantyNoticeMain IconsSecondary IconsCautionWarningInstallationCustomerAssistance26 English Included In This Package IntroOperationCustomerAssistanceWarrantyNoticeSecondary And Start-Up Included In This Package • You should find all of the following items in the package with your CobraMarine™ VHF radio: Transceiver* Transceiver Flush Mount Kit Microphone Transceiver Surface Mount Kit Operating Instruction Manual Warning Sticker GPS Interface Cable Microphone Mounting Kit * The term transceiver will be used to identify the main unit containing the LCD screen and controls. Radio will be used to identify the entire equipment including transceiver, microphone, antenna, and any attached external speakers. Nothing comes close to a Cobra® Mounting AndPowering The Radio 27 IntroOperationCustomerAssistanceWarrantyNoticeSecondary And Start-Up Mounting And Powering The Radio • Before using your CobraMarine™ VHF radio, it must be installed on your vessel. Installing Your Radio Choose a location for your radio where it will be conveniently accessible with the following factors in mind: n The leads to the battery and the antenna are best kept as short as possible. n The antenna must be mounted at least three (3) feet from the transceiver. n The radio and all speakers need to be far enough from any magnetic compass to avoid deviation due to the speaker magnet. n There needs to be free air flow around the heat-sink fins on the back of the transceiver. Surface Mount A Surface Mounting kit is included with your CobraMarine™ VHF radio to allow its installation on almost any flat surface. To Mount The Transceiver On Almost Any Flat Surface: 1. Use the mounting bracket as a template to drill holes for the mounting screws. 2. Attach the mounting bracket to the chosen surface. 3. Attach the transceiver to the mounting bracket with the locking knobs. 4. Tilt the transceiver to a convenient angle and tighten the locking knobs. Surface Mounting Kit Tilt Lock Knobs IntroOperationCustomerAssistanceWarrantyNoticeMain IconsSecondary IconsCautionWarningInstallationCustomerAssistance26 English Included In This Package IntroOperationCustomerAssistanceWarrantyNoticeSecondary And Start-Up Included In This Pac...