Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
If that is needed, please follow the instructions below. 1. turn off the machine, and unplug it from the outlet. Remove portable spot cleaner. 2. Remove the nozzle by unscrewing three WARNING: to reduce the risk of fire, electric shock or injury, unplug from the outletbefore servicing. screws on the nozzle cover. 3. turn the machine on its side. ImPORTANT: with portable spot cleaning pedal facing down. 4. Remove end cap by unscrewing the 3 screws. take care not to drop the screws into the unit. 5. Remove 1 silver screw from the pivot arm. 6. Remove pivot arm by gently lifting up. 7. Remove small brush belt. 8. Replace small brush belt, and reverse steps above. 9. manually rotate brushes by hand to make sure they move freely. may notice a slight resistance from the motor. 2. 4. 6. 5. 8. 7. 14 800.237.7691 Maintenance and care Maintenance and care Brush removal and large belt replacement (as needed) Brushes can be removed for cleaning or replacement as needed. WARNING: 1. follow small belt removal instructions on page 14 items 1-7. to reduce the risk of fire, electric shock or injury, 2. Remove brush rolls by pulling them off unplug from the outletof the metal rods. Be careful not to before servicing. lose the small washer at each end of the brush rolls. 2. 3. Re-attach the large belt to the grooves on the end of the new brush rolls. if the belt is damaged, replace with a new belt. 4. Place cleaned or new brush rolls back onto the rods. make sure one washer is on each end of the rollers prior to sliding onto the rod. be sure the brush is seated completely on the rod. 5. Replace small belt over grooves in back roller and metal cog. 6. Replace pivot arm and secure with silver screw. 7. Re-attach end cap by tightening with the (3) black screws. 8. Return front nozzle to front of unit, by latching from underneath and then securing with 3 screws. 9. follow step number 8 & 9 on page 14. if you have any questions or are having trouble installing or replacing your belt(s) or brushes, please call BISSELL Consumer Services. 3. 4. 6. 8. 5. 7. 800.237.7691 15 Troubleshooting Built-in heater ready light does not illuminate Possible causes Remedies 1. The power is not turned ON 1. The power must be ON to activate the heater ready light 2. The portable spot cleaner is not attached completely 2. Make sure the portable spot cleaner is attached Push down firmly to check Reduced Spray or No Spray Possible causes Remedies 1. Formula & water tank may be empty 1. Refill tank 2. Formula & water tank may not be seated completely 2. Turn power OFF. Remove and reseat tank 3. Pump may have lost prime in portable spot cleaning mode 3. Hold end of hose below water level in tank to prime 4. The portable spot cleaner is not attached completely 4. Push down firmly to check connection 5. Solution filter may be clogged 5. Follow steps under cleaning filter on page 13 DirtLifter® PowerBrush does not turn Possible causes Remedies 1. The portable spot cleaner is not attached completely 1. Make sure the portable spot cleaner is attached. Push down firmly to check 2. The unit is in the upright position 2. Brushes only rotate when unit is reclined using the recline pedal 3. Circuit breaker on machine (if equipped) may have tripped 3. Turn the machine OFF and unplug from outlet. Check to see if foreign object is caught in brush roll. Remove object. Plug machine in to reset circuit breaker 4. The belt is off or broken 4. Turn power OFF and unplug unit from outlet. Follow instructions on pages 14 and 15 Loss of suction power Possible causes Remedies 1. Tanks may not be seated properly 1. Pick up both tanks and reseat them so it they fit snugly on the unit 2. Nozzles may not be assembled properly 2. Unplug the unit. Check to make sure the "lip" of the nozzle is securely hooked into the groove on bottom of Tank (see page 10) 3. The portable spot cleaner is not attached completely 3. Make sure the portable spot cleaner is attached. Push down firmly to check 4. Dirty tank has picked up maximum amount of 4. Empty dirty tank dirty water and has reached full line 5. Formula & water tank is empty 5. Check fluid levels in formula & water tank 6. Suction Gate is open. 6. Check to make sure the suction gate is closed. Follow “Cleaning Suction Gate” instructions on page 13. Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product. Please do not return this product to the store. For any questions or concerns, BISSELL is happy to be of service. Contact us directly at 1-800-237-7691. 16 800.237.7691 Accessories - BISSELL deep cleaner Accessories - BISSELL deep cleaner Item Part No. Part Name 1 203-6651 3” tough stain tool 2 203-6652 Powered turbobrush® hand tool 3 203-6653 4” upholstery tool 4 203-6654 6” stair tool 5 203-7885 spraying crevice tool 6 7 8 203-7412 62e5-2 99K5-2 deep Reach Pet tool 2X fiber cleansing for...
Эта инструкция также подходит к моделям:Пылесосы - 35K3 (2 mb)
Пылесосы - 73H5 (2 mb)
Пылесосы - 94Y2 (2 mb)