Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
2. using the brush on the tool, gently scrub the area to be cleaned. 3. apply downward pressure on the tool and pull it toward you. the suction will remove the dirt and cleaning solution. continue until no more dirt can be removed. Adsdfdd ghg bvhcvbbj jkn hnbjgcghh fhl kl Manufacturer’s tag ImPORTANT Check for colorfastness in an inconspicuous place. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric 800.237.7691 11 Operations Portable spot cleaning mode continued Cleaning with Deep Reach™ Tool 1. set tool on soiled surfaces and press the trig-1. ger to spray solution onto the soiled area to be cleaned. 2. slowly move the tool back and forth over the soiled surface, keeping the tool in contact with the carpet. 3. Release trigger and move tool slowly over the soiled area to suction up water and dirt. 4. continue to clean the area, working in small sections, until no more dirt can be removed. Empty dirty tank Follow the instructions under Empty dirty tank section on page 9 of the Upright cleaning mode section. Replacing portable machine on base graphic 1. align the product as the graphic shows, with the cord side on the left and hose side on the right. 2. Push down the portable spot cleaner until you hear it click securely into place. test the fit by pulling up on the carry handle to make sure it is secure. Cleaning portable machine 1. Remove and rinse the tools in clean, running water. dry and replace in the tool storage provided. 2. it is recommended that you suction clean water from a bowl to rinse out the hose. then lift end of hose and stretch out to ensure all water is cleared from hose. 3. coil flex hose around the hose wrap and secure with latch. 4. check suction gate and if it appears dirty, follow steps 1-4 under cleaning suction gate on page 13. 1. 12 Maintenance and care machine care (check regularly) Cleaning suction gate The suction gate automatically diverts air when the portable deep cleaner is detached. This should be checked and cleaned regularly for any dirt and debris. 1. step on the pedal and remove the portable spot cleaner. Remove dirty tank. 2. Remove two screws and pull off suction gate door. 3. Wipe suction gate clean and rinse suction gate door. 4. Replace suction gate door and two screws. Cleaning spray tips 1. step on the pedal and remove the portable spot cleaner. to remove, push in tab and pull it out. 2. clean by rinsing under hot water. 3. Replace by snapping back in. 4. Repeat steps on second spray tip. Cleaning solution filter 1. step on the pedal and remove the portable spot cleaner. Remove the red solution filter cap on the base of the machine by inserting a coin or a flat head screw driver into the slot on the top. 2. turn counter clockwise to unscrew. set aside. 3. Remove the white filter by the post. Rinse the filter under water. 4. Replace the white filter back into the filter area. Note: make sure the white filter is seated properly before replacing the red solution filter cap. 5. Replace the red solution filter cap and turn clockwise to tighten. WARNING: to reduce the risk of fire, electric shock, or injury, turn power off and disconnect plug from electrical outlet before performing maintenance or troubleshooting. 2. Suction gate Spray Tips 1. 2. Solution Filter Cap 3. 5. Filter 800.237.7691 13 Maintenance and care Small belt removal and replacement (as needed) Occasional replacement of one or both belts may become necessary. If that is needed, please follow the instructions below. 1. turn off the machine, and unplug it from the outlet. Remove portable spot cleaner. 2. Remove the nozzle by unscrewing three WARNING: to reduce the risk of fire, electric shock or injury, unplug from the outletbefore servicing. screws on the nozzle cover. 3. turn the machine on its side. ImPORTANT: with portable spot cleaning pedal facing down. 4. Remove end cap by unscrewing the 3 screws. take care not to drop the screws into the unit. 5. Remove 1 silver screw from the pivot arm. 6. Remove pivot arm by gently lifting up. 7. Remove small brush belt. 8. Replace small brush belt, and reverse steps above. 9. manually rotate brushes by hand to make sure they move freely. may notice a slight resistance from the motor. 2. 4. 6. 5. 8. 7. 14 800.237.7691 Maintenance and care Maintenance and care Brush removal and large belt replacement (as needed) Brushes can be removed for cleaning or replacement as needed. WARNING: 1. follow small belt removal instructions on page 14 items 1-7. to reduce the risk of fire, electric shock or injury, 2. Remove brush rolls by pulling them off unplug from the outletof the metal rods. Be careful not to before servicing. lose the small washer at each end of the brush rolls. 2. 3. Re-attach the large belt to the grooves on the end of the new brush rolls. if the belt is damaged, replace with a new belt. 4. Place cleaned or new brush rolls back onto the rods. make sure one washer is on each ...
Эта инструкция также подходит к моделям:Пылесосы - 27F6 (2 mb)
Пылесосы - 35K3 (2 mb)
Пылесосы - 94Y2 (2 mb)