Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
4. Repeat motion over same area without depressing Trigger. 5. Repeat Steps 3 and 4 until no more dirt can be removed. 6. Continue to clean entire carpet, working in 3’ x 4’ sections. 7. Empty the Dirty Water Tank Assembly when dirty water reaches the fill line. 8. If the machine loses suction and/or motor noise rises in pitch, turn Power Switch to OFF. Check the Dirty Water Tank Assembly and empty the tank if it is full [see WHEN YOU’RE DONE, page 6]. 9. If floor nozzle stops spraying, turn Power Switch to OFF and check water/cleaning solution mixture level. Refill if needed. Never run POWERSTEAMER® dry. Tip: Deep cleaning stairs and high traffic areas on a regular basis can prolong carpet life. CAUTION: The Dirty Water Tank Assembly holds approximately one gallon of soiled liquid. A special float device in the tank will cause the cleaner to stop removing solution from carpet, and the motor sound to rise in pitch when the Dirty Water Tank Assembly is full. Failure to empty full tank will damage unit. When you’re done 1. Turn Power Switch to OFF (O) position. 2. Unplug Power Cord from outlet. 3. Remove and empty Clean Water Tank Assembly. 4. Press Release Pedal and tip Handle Assembly back with Handle Assembly. 5. Release Dirty Water Tank Latch Assembly at bottom of Lower Chassis. 6. Carefully lift Dirty Water Tank Assembly from Lower Chassis using Carry Handle Assembly. 7. Carry Tank to a toilet or sink, turn Circular Cap at back of unit counterclockwise to open, and pour to empty. 8. Fill Dirty Water Tank Assembly with clean water. Rinse thoroughly and discard water. 9. Remove Dirty Water Tank Triangle Lid and flush suction opening with clean water. Replace cover. Replace Circular Cap by turning clockwise. 10. Replace Clean Water Tank Assembly on Handle Assembly and secure with side latches. 11. Replace Dirty Water Tank Assembly on Lower Chassis and secure with Clean Water Tank Latch Assembly. 12. See PUTTING IT AWAY on page 7. How to clean upholstery and small areas How to clean upholstery and small areas Getting ready 1. Unfasten the Clean Water Tank Assembly by lifting from the bottom with your fingers. 2. Tip Handle Assembly back by pressing Release Pedal on left side of Lower Chassis and pulling back on Handle Assembly. 3. Remove Dirty Water Tank Triangle Cap by pulling back on snap tab with finger. 4. Place triangle-shaped end of Flex Hose Assembly in Dirty Water Tank Triangle port by placing wide (bottom) end in first, then pushing latch end in until it snaps into place. 5. Tip Handle Assembly back to its full upright position. 6. Place Solution Tube Connector into the port at the lower left side of the Handle Assembly. Place tabs on Connector into notches in port, then turn clockwise to secure. Make certain Solution Tube is securely fastened to Connector. 7. Attach Cleaning Tool to Flex Hose Assembly using the “button-in-hole” method. 8. Take Clean Water Tank to sink area, remove Clean Water Tank Cap and fill Tank with hot (NOT boiling) tap water to fill line. Fill Tank Cap to fill line with Fiber Cleansing Formula and pour into Clean Water Tank. Replace Cap securely. 9. Replace Clean Water Tank Assembly. Slide Tank down front of Handle Assembly until it fits snugly against top of Lower Chassis. Secure with Clean Water Tank Latch Assembly. 10. Unwrap Power Cord from Cord Holder and plug into 120 Volt, 60 Hz grounded outlet as described in Important Safety Instructions, page 2. If cleaner starts when first plugged in, switch off until ready for use. Cleaning 1. Slowly move Cleaning Tool back and forth over soiled surface, first using spray only, then spray and vacuum, finishing with vacuum only. 2. Continue to clean soiled area, working in small sections, until no more dirt can be removed. Do not overwet. 3. If the machine loses suction and/or motor noise rises in pitch, turn Power Switch to OFF. Check the Dirty Water Tank Assembly and empty the tank if it is full [see WHEN YOU’RE DONE, page 6]. 4. If spray tip stops spraying, turn Power Switch to OFF and check water and cleaning solution level. Refill if needed. Never run POWERSTEAMER® dry. CAUTION: Do not lay unit on its back with Clean Water Tank Assembly in place. Do not tip up foot with Dirty Water Tank Assembly in place. Tip: Check upholstery stuffing before cleaning. Colored stuffing may bleed through fabric when wet. Putting it away 1. Follow instructions in WHEN YOU’RE DONE, page 6. 2. Disconnect Solution Tube Connector by turning it counterclockwise and gently pulling it straight from port. 3. Remove Flex Hose Assembly from Dirty Water Tank Triangle port. 4. Replace Dirty Water Tank Triangle Cap. 5. Return Attachment Hose to storage rack. 6. Wrap Power Cord around Cord Holder on back of POWERSTEAMER.® 7. Wipe all surfaces with a soft cloth. 8. Store cleaner upright in a protected, dry area. NOTE: Never leave clean water in the Clean Water Tank Assembly or soiled solution in the Dirty Water Tank Assembly. Troubleshooting Troubleshooting Re...
Эта инструкция также подходит к моделям:Пылесосы - 1691 (248.4 kb)