Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Ask for HOOVER part no. 40308001. To store scub module , remove scrub module from tool in same manner as removing the brush module. Align openings on back of module with tabs in storage area (G). Push module into position. Afte r using tool 1. Follow steps a and b for "After cleaning on pages 9 & 10. 2. Rinse tool and hose by filling sink with a small amount of water. Turn deep cleaner ON and pickup the water with the tool. Cleaning carpeted stairs Read “Before you begin cleaning” instructions on page 9. 1. Place handle in upright position. Agitator brushes will not rotate while handle is in upright position. 2. Fill clean solution tank with HOOVER Carpet/Upholstery Detergent according to instructions for Figs. 2-9 to 2-15. 3. Attach tool to end of hose. 4. Hose length may require that machine be placed at the top of the stairs to clean upper half of stairway and at bottom of stairs to clean lower half. To prevent machine from falling, use extra caution when cleaning on stairs. Do not place deep cleaner on stairs. Do not point tools toward people or pets. 5. Dry hands and plug deep cleaner into a properly grounded outlet. 6. Turn deep cleaner ON. If necessary, refer to "Before using tool" section to remove air from the system. 7. Pre-s pray the carpeted stair by holding the tool (A) or (B) about one inch above the carpet and push it forward while pressing the trigger (equals one wet stroke). 8. Position tool against the riser and slightly press it into carpet pile. Press the trigger and pull the tool slowly over the carpet (second wet stroke). Release trigger at end of stroke. 12 9. Lift tool, and position it against riser. Pull tool slowly over carpet without pressing trigger (dry stroke). It is best to alternate wet and dry strokes as described above. End with more dry strokes and watch for the green 'MAX Extract' light to come on to aid in faster drying of carpet. 10. Overlap strokes by 1/2 inch to help prevent streaking. To avoid saturating carpet, do not use more than 4 wet strokes over any one area. Always end with dry strokes. If additional cleaning is necessary, wait until the carpet is completely dry before using the tool again. 11. Empty recovery tank when the red 'MAX Extract' light comes on and the motor sound becomes higher pitched and there is a loss in suction (see "Automatic shut-off”, Fig. 2-7). When finished cleaning, follow "After cleaning instructions on page 9 and "After using tool" instructions on page 12. Cle aning upholstery Read “Before you begin cleaning” instructions on page 9. Be sure to check the cleaning code on your upholstery. Use your deep cleaner only on upholstery marked “W”or “W/S”. 1. Place handle in upright position. Agitator brushes will not rotate while handle is in upright position. 2. Fill clean solution tank with HOOVER Carpet/Upholstery Detergent according to instructions for Figs. 2-9 to 2-15. 3. Attach tool to end of hose. Do not point tools toward people or pets. 4. Dry hands and plug deep cleaner into a properly grounded outlet. 5. Turn deep cleaner ON. If necessary, refer to "Before using tool" section to remove air from the system. 6. Gently press the tool onto the fabric. Press the trigger and slowly pull the nozzle over the fabric. 7. Overlap strokes by 1/2 inch to help prevent streaking. Make no more than 2 passes with the solution over any one area to prevent over-wetting and damage to fabric. If additional cleaning is necessary, wait until the upholstery is completely dry before using the tool again. 11. Empty recovery tank when the red 'MAX Extract' light comes on and the motor sound becomes higher pitched and there is a loss in suction (see "Automatic shut-off", Fig. 2-7). When finished cleaning, follow "After cleaning" instructions on page 9 and "After using tool" instructions on page 12. 4. Maintenance Head I ight replacement Wh at to buy The deep cleaner uses a 7 volt, wedge base type bulb, HOOVER part no. 27313106. Wh e re to buy Bulbs may be purchased from authorized Hoover dealers (Depot), Hoover Factory Se rvice Centers, or through The Hoover Company online at h oover. com. Make additional strokes without pressing the trigger to remove more moisture. Also, periodically checking the 'MAX Extract' lights will help ensure that the maximum amount of water has been removed. 8. To clean in corners or creases, lift the tool one-half inch from the fabric and press the solution trigger. The crevice tool is very useful for this task. 9. Vacuum up the solution with the tool without pressing the trigger. 10. For heavily soiled areas, it may be necessary to repeat the cleaning process. Make crisscrossing strokes to the original pattern; overlap each pass. How to repl a ce Turn cleaner off and with dry hands, disconnect deep cleaner from electrical outlet. 1. Using a Phi llips screwd ri ver, rem ove the screw as shown and lift off lens. Continued ^ 13 2. Pull old bulb straight out of socket. ...