Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Leaving it for an extended period of time may cause it to set and become permanent 1. blot up liquids with an absorbent cloth or paper towels. White materials are recommended because certain dyes may bleed and make the stain worse. 2. gently scrape up any semi-solids with a spoon or spatula. do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery. 3. if the area has dried, remove the remaining semi-solids and residue with a sweeper or vacuum. 4. be sure to test any spot removal formulas in an inconspicuous area first. this is important as some dyes and materials could be damaged or discolored by cleaning solvents. if such a change should occur, try a different solution or call a professional. 5. if cleaning on berber carpeting, gently run your machine over a hidden area. if no fuzzing occurs, continue cleaning in soiled area. 6. using the bissell tough stain Precleaner, spray evenly over soiled area. DO NOT OVERWET. Wait 3-5 minutes. gently work the solution by blotting area with a clean, damp, color safe cloth. 7. clean using the unit or the hose with attachment. 12 800.237.7691 Maintenance and care Maintenance and care Machine storage Once your cleaning is complete, make sure both the dirty and clean water tanks are emptied, rinsed out and dried before the next use. Note: Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty. Machine care For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete 1. turn power off (0). unplug the machine and wrap the power cord. 2. after emptying the clean and dirty water tanks, rinse them out with running hot tap water. 3. the top half of the dirty water tank can also be rinsed clean through the nozzle area. 4. to clean attachments, remove from hose and rinse in clean, running water and let dry. clean the hose by removing it from the machine and let running tap water run through both ends. 5. after carpet is dry, vacuum again to remove hair and fuzz. 800.237.7691 13 Maintenance and care Belt removal and replacement 1. turn off the machine and unplug it from the outlet. 2. Remove the dirty and clean water tanks from the base of the machine. 3. While standing behind the unit, lay the unit on its’ side (cord side up) 4. looking at the bottom of unit, find the back center of the brush carriage where the carriage latch is located. it is between the brush assembly and the front wheels. 5. Pull brush carriage towards you with one hand until it stops, then pinch the carriage latch with other hand while 4. 5. pulling the carriage towards you. the carriage should swing out to access belt cover. 6. Remove three screws from cover. lift and remove to access brush carriage. 7. turn the belt inward towards the large pulley while lifting out. 6A. 6B. 8. Place new belt over small pulley first and then slip the belt over the large pulley. 9. Replace the brush carriage and screws. 10. Push brush carriage back into place making sure the carriage latch locks back into place. 7. 8. 3. WARNING: to reduce the risk of fire, electric shock, or injury,turn power off and disconnect plug from electrical outlet before performing maintenance or troubleshooting. 9. 10. 14 800.237.7691 Maintenance and care Brush removal and replacement 1. turn off (0) the machine and unplug from the outlet. 2. Remove the dirty and clean water tanks 3. Maintenance and care Brush removal and replacement 1. turn off (0) the machine and unplug from the outlet. 2. Remove the dirty and clean water tanks 3. from the base of the machine. 4. 3. While standing behind the unit, lay the unit on its’ side (cord side down). 4. looking at the bottom of the unit, find the center of the brush carriage where the carriage latch is located. it is between the brush assembly and wheels. 5. Pull the brush carriage towards you with one hand until it stops. Pinch the carriage latch with the other hand while pulling the carriage towards you. the carriage should swing out to access brush end cover. 6. Remove three screws from endcap. Pull 6A. 6B. endcap off to release brush roll. 7. With cover removed, the brush comes out easily by tilting the loose end out of the carriage. 8. to replace the brush roll back into the unit, place the large open end of the 7. 8. brush onto the carriage and tilt opposite end back into place. (same image as 7, just change arrow direction) 9. With the brush sitting relatively straight up and down by itself, place endcap back on top and replace three screws. the brush will need to be held and cen9. 10. tered to the cover while placing it back on. 10. spin the brush by hand to make sure it turns freely with some minor resistance from the motor. Push brush carriage back into place with a light pull against the lock. 5. 800.23...
Эта инструкция также подходит к моделям:Пылесосы - BIGGREEN 40M1 (1.94 mb)