Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
It has been pre-programmed by your installer and contains what is known as a configuration file that contains all the codes, graphical buttons and navigation behaviour. VGA touch screen Firm keys Backlight key Stylus Hard keys Cursor keys Rotary wheel VGA touch screen Firm keys Backlight key Stylus Hard keys Cursor keys Rotary wheel Taking a First Look Control Panel USB connector This connector is used by the installer to configure the Control Panel. Speaker Docking station Panel connector Power adapter Docking connector Power switch TSU9600 Starter’s Guide Charging the Control Panel When the Battery level icon on your screen turns red, it is time to charge the Control Panel. The Control Panel will operate from one to several days depending on how your installer has configured it. Note The service life of the battery depends on the timeout settings and wireless network settings configured by your installer. Please contact your installer if you notice that the battery is deteriorating. When you place the Control Panel in the docking station, the red Charging LED on the front of the docking station lights up. When the Charging LED fades out, it means that the Control Panel is fully charged. This can take 3 to 4 hours. If the battery is low and the Charging LED does not light up, make sure that: • the power switch at the bottom of the Control Panel is switched to 1. • the docking station is plugged into the mains. The docking station glows when it is plugged in. • the Control Panel is located properly in the docking station. • the panel connector is clean and free of obstructions. Tip IIt is recommended that the Control Panel be placed in the docking station after use. The Control Panel still consumes power even while its screen has turned black. Enjoying Your Pronto Control Panel Controlling Your Home Theatre Activating the Control Panel screen • Tap the touch screen with the stylus included with the Control panel or with your finger. -Or • Press the Backlight key. TSU9600 Starter’s Guide Depending on the settings entered in the Screen Settings page, the screen will also activate if you: • Tilt the Control Panel sufficiently towards you. Note The screens on your Control Panel are customised by your installer and may differ in appearance from that shown above. Operating the Control Panel Buttons on the touch screen These buttons are used to •Start an activity in the Home Theater • Control the individual devices in the Home Theater Firm keys Firm key actions are activity-related and may vary depending on the page displayed on screen. Battery level WiFi activity WiFi strength (4 levels) No identification No connection No No network icon Hard keys on the Control Panel The hard keys on the Control Panel have set functions in the various Home Theatre activities. . 50° -or • Press one of the 5 firm keys below the screen or one of the hard keys. Note The following keys send commands to your equipment without activating the screen: Channel Up/Down, Volume Up/Down, Menu, Guide, Power, Mute TSU9600 Starter’s Guide Turning the Control Panel On/Off Power switch The Power switch on the bottom of the Control Panel turns the Control Panel on and off. Tip Always switch the Control Panel off during transport to prevent the touch screen from being activated and draining the battery. Changing the Pronto Settings Note Your installer may have blocked access to the Settings pages. Normally, your installer will have fully programmed your Control Panel and no changes are required. To open the Settings pages: • Press and hold the Settings icon for more than 3 seconds. General Version and network information as well as adjust the volume settings. General volume Button volume covers all the sounds applies specifically to you hear when you the default sound you operate the Control hear when you press Panel. a button. Tip Press and hold the ‘-’ and ‘+’ buttons to increase or decrease the setting faster. memory status can be found on the Info Page. To change Date & Time settings 1 Tap the Month, Day, Year or Time button. This highlights the button. 2 Tap the ‘-’ and ‘+’ buttons to adjust the date or time. To change the Volume settings • Tap the ‘-’ and ‘+’ buttons to To access the other Settings pages: • Tap the different tabs. TSU9600 Starter’s Guide Screen To change the Activation Settings • Tap the buttons to toggle between the various Activation settings: Pick up sensor: the Control Panel switches on when it is tilted. Firm keys: the Control Panel switches on and/or sends out an IR signal when a firm key is pressed. Cursor keys: the Control Panel switches on and/or sends out an IR signal when one of the cursor keys is pressed. To calibrate the touch screen: To change the Time out and To exit the 1 Tap the Calibrate button. the Brightness settings: Settings pages: 2 Follow the on screen instructions • Tap the ‘-’ and ‘+’ buttons • Press the right to tap the 4 corners of the screen. to adjust the settings. firm key The touch screen is no...
Эта инструкция также подходит к моделям:Телевизоры - TSU9600/37 (239.73 kb)
Телевизоры - TSU9600/00 (239.73 kb)