Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
MENU C. Change Code Although the default code “0000” is supplied with the unit, you can set your own code. 4 Use [CH K /L] to select “CHANGE CODE”, then press [VOL X]. e.g.) analog TV mode or CH CH VOL TV RATING MPAA RATING CHANGE CODE 5 Press [the Number buttons] on the remote control to enter the new 4-digit code. • Enter code again in “CONFIRM CODE” space. –/ENT 1 2 3 4 5 6 8 9 0 +100 7 NEW CODE _ _ _ _ CONFIRM CODE _ _ _ _ 6 Press [MENU] to exit. MENU Note: • Make sure new code and confirm code must be exactly the same. If they are different, the space is cleared for reentering. • Your code will be erased and return to the default (0000) when a power failure occurs or when you turn off the power using a wall switch. If you forget the code, unplug the power cord for 10 seconds to restore the code to 0000. 23 EN WATCHING INTRODUCTION CONNECTION INITIAL OPTIONAL TROUBLESHOOTING INFORMATION D.S.T. DTV After the initial setting you set when you fi rst turned on the power, you can set the D.S.T. (daylight saving time) again. When you set this function to ON, the clock will automatically move forward one hour at 2:00 a.m on the fi rst Sunday in April and move back one hour at 2:00 a.m on the last Sunday in October. 1 Press [MENU] to display the main menu. MENU 2 Use [CH K/L] to select “DTV SET UP”, then press [VOL X]. e.g.) digital TV mode or CH CH VOL PICTURE CHANNEL SET [ENG]/ESP/FRA V-CHIP SET UP CAPTION [OFF] DTV SET UP 3 Use [CH K/L] to select “D.S.T. (Daylight Saving Time)”, then use [VOL X/Y] to set to “ON” or “OFF”. or CH CH VOL or VOL DTV DISPLAY [LETTERBOX] DTVCC D.S.T.(Daylight Saving) [- - -] TIME ZONE [ALASKA] 4 Press [MENU] to exit. MENU Note: When you set D.S.T. to "OFF", the date and time information adjusted for the area set by "TIME ZONE" is displayed. .. Time Zone DTV If you move the TV to a diff erent area after the initial setting you set when you fi rst turned on the power, you can set the area again. 1 Press [MENU] to display the main menu. MENU 2 Use [CH K/L] to select “DTV SET UP”, then press [VOL X]. e.g.) digital TV mode or CH CH VOL PICTURE CHANNEL SET [ENG]/ESP/FRA V-CHIP SET UP CAPTION [OFF] DTV SET UP 3 Use [CH K/L] to select “TIME ZONE”. or CH CH DTV DISPLAY [LETTERBOX] DTVCC D.S.T.[Daylight Saving] [ON] TIME ZONE [ALASKA] 4 Use [VOL X/Y], the time zone will be switched as below. VOL or VOL [ALASKA] [HAWAII] [ATLANTIC] [PACIFIC] [EASTERN] [MOUNTAIN] [CENTRAL] • Based on the world standard time information acquired from digital broadcasting, the time difference will be adjusted as below. ALASKA -9 hours HAWAII -10 hours PACIFIC -8 hours MOUNTAIN -7 hours CENTRAL -6 hours EASTERN -5 hours ATLANTIC -4 hours 5 Press [MENU] to exit. MENU .. 24 EN TROUBLESHOOTING Troubleshooting Guide If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart once before calling for service. .. Symptom Remedy No power • Be sure the power cord is plugged in. • If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to reset itself. No picture or sound • Check if the power is on. • Check the outlet connection. • Check the antenna or cable connection to the main unit. • When the outside antenna is used, check the wire condition and connection. • View other TV channels. The problem might be limited to the broadcasting station. • Turn off the power and wait for about 1 minute, then turn it on again. No color • Check the antenna or cable connection to the main unit. • When the outside antenna is used, check the wire condition and connection. • View other TV channels. The problem might be limited to the broadcasting station. • Adjust “COLOR” in “PICTURE” menu. Sound OK, picture poor • Check the antenna or cable connection to the main unit. • When the outside antenna is used, check the wire condition and connection. • Electrical interference from nearby appliances may affect picture quality. • Adjust “CONTRAST” and “BRIGHT” in “PICTURE” menu. • View other TV channels. The problem might be limited to the broadcasting station. Picture distorted • When the outside antenna is used, check the wire condition and connection. • View other TV channels. The problem might be limited to the broadcasting station. Weak picture • Check the antenna or cable connection to the main unit. • When the outside antenna is used, check the wire condition and connection. • Adjust “CONTRAST” and “BRIGHT” in “PICTURE” menu. • View other TV channels. The problem might be limited to the broadcasting station. Lines or streaks in picture • When the outside antenna is used, check the wire condition and connection. • Electrical interference from nearby appliances may affect picture quality. • View other TV channels. The problem might be limited to the broadcasting station. Picture blurred • When the outside antenna is used, check the wire condition and connection. • View other TV channels. The problem might be limited to the broadcasting station. Ghosts in pict...