Оценок - , средний балл:
(
)
)
Производитель: Lennox Hearth
Размер: 11.03 mb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Figure 6 Cut Wire Ties If Provided Locate The TV IR Cable Figure 7 Twist And Tape Figure 8 Pull To Replace Step 17. Pull the TV IR cable until the new cable is out. Unwrap the tape and discard the old cable (seeFigure 8). Step 18. Locate the Remote Control receiver through the rectangular slot and pull the cables out and cut the ends free, enough to wrap the end of the new receiver. Then fish them through the rectangular hole while pulling, to route through the frame cavity (seeFigure 9. ) Step 19. Push the Remote Control receiver into the rectangular slot (refer toFigure 10). Figure 9 Pull Remote Receiver Cables Out Figure 11 Step 20. Bundle the new cables and the A/V cables together and wrap with masking tape, or rout them through the flexible conduit if provided. SeeFigures 11 and 12. Step 21. Tack the wire harness into the side frame and replace the wire harness shield, if provided (seeFigure 13). Figure 12 Figure 13New Cables Routed Figure 10 Push The Remote Receiver Into The Rectangular Slot Bundle New Cables And A/V Cables Together With Tape Tack Wire Harness Behind Side Frame Figure 11 Step 20. Bundle the new cables and the A/V cables together and wrap with masking tape, or rout them through the flexible conduit if provided. SeeFigures 11 and 12. Step 21. Tack the wire harness into the side frame and replace the wire harness shield, if provided (seeFigure 13). Figure 12 Figure 13New Cables Routed Figure 10 Push The Remote Receiver Into The Rectangular Slot Bundle New Cables And A/V Cables Together With Tape Tack Wire Harness Behind Side Frame Step 22. Place the Control Board against the back wall and attach using the top four (4) outermost holes with the screws and nuts provided. Refer toFigures 14 and 15. Step 22. Place the Control Board against the back wall and attach using the top four (4) outermost holes with the screws and nuts provided. Refer toFigures 14 and 15. Figure 14 Back Wall With Mounting Holes Back Wall With Mounting Holes Power Heater Lamp TV/DVD Blower Attach With Screws Here Attach With Screws Here TV DVD Display Figure 15 Mount The Control Board Using The Screws And Nuts Provided NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. DVD INSTALLATION INSTRUCTIONS DVD INSTALLATION INSTRUCTIONS Step 1. Before installing the DVD player, connect the new DVD player to an electrical outlet and insert the DVD disc into the drawer. Step 2. Disconnect the DVD player and bring it into the fireplace cavity. Step 3. Proceed to connect the A/V cables as labeled. Connect the power cord. Step 4. Place a piece of Velcro on the DVD player eye and attach the IR transmitter unit to it (seeFigure 16). Step 5. With the controls facing to the right hand side, tilt the DVD player sideways under the front frame, to insert it into position. Step 6. Using the new remote control, test the fireplace for proper operation. Step 7. Strap the DVD player (seeFigure 17). Step 8. Re-assemble the fireplace parts in reverse order. Figure 17 Strap The DVD Player Figure 16 Attach A/V Cables And IR Transmitter Unit NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. NOTE: THIS PAGE INTENTIONALLY LEFT BLANK. The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. 1110 West Taft Avenue P/N 750,251M REV. A 01/2008 Orange, CA 92865 ...
Эта инструкция также подходит к моделям:Пульт ду - H6977 (11.03 mb)