Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Remove the grate. This Remote Control Replacement Kit is to be used to replace the Reflections Electric Fireplace’s Remote Control. The kit components are shown below. (Kit Number H1454 And/Or H6977) REPLACEMENT INSTRUCTIONS Note: Depending on the type of control board in your fireplace, the number of steps and components may vary. Following are the types of control boards for identification: If you have Kit Number H1094, it will be necessary to replace the board and IR cables. In this case, complete all the Steps as outlined in these instructions. If you have Kit Numbers H1454 or H6977, it is not necessary to replace the IR cables. In this case, skip Steps 11 through 21 and complete the remaining process as outlined in these instructions. Refer to the Reflections Fireplace Installation Instructions manual (No. 850,091M) for a visual aid on the following steps: Step 1. Disconnect the electrical power to the fireplace. Step 2. Remove the doors from the fireplace. Step 3. Remove the reflective glass. Step 4. Remove the logs. Step 6. Remove the ember bed. Step 7. Remove the fireplace floor. Step 8. Remove the DVD player. Make sure to label the “Video Out” and “Sound Out” cables when disconnected from the DVD player. Figure 1 (Kit Number H1094) Plastic Holders Control Board Figure 2 IR Cables NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Step 9. Locate the fireplace control board (Kit Number H1094) and remove it, including the plastic holders (Refer toFigure 1). Step 9. Locate the fireplace control board (Kit Number H1094) and remove it, including the plastic holders (Refer toFigure 1). Step 11. Locate the wire harness behind the right hand side frame. Step 12. Some early units may have a metal wire shield (Figure 3). Slide the shield upwards to align the slots to the screws and remove. Figure 3 Wire Shield Step 13. Pull the wire harness completely outside the cavity and remove the flexible wire conduit to expose the wires completely (some early units may have binding tape). If provided, save the flexible conduit to re-use. Step 14. Leave the A/V cables in place. These cables are not being replaced with the Remote Control Kit. Refer toFigures 4 and 5. Figure 4 Bottom Side View Figure 5 A/V Cables Upper Side View NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Step 15. Locate the TV IR cable and cut about five (5) inches from the end (seeFigure 6). Step 16. Twist the connector end of the new IR cable to the ends of the old IR cable and wrap securely with duct tape. Refer toFigure 7. Note: Free all cables from one another and pull them individually, as they are replaced. Figure 6 Cut Wire Ties If Provided Locate The TV IR Cable Figure 7 Twist And Tape Figure 8 Pull To Replace Step 17. Pull the TV IR cable until the new cable is out. Unwrap the tape and discard the old cable (seeFigure 8). Step 18. Locate the Remote Control receiver through the rectangular slot and pull the cables out and cut the ends free, enough to wrap the end of the new receiver. Then fish them through the rectangular hole while pulling, to route through the frame cavity (seeFigure 9. ) Step 19. Push the Remote Control receiver into the rectangular slot (refer toFigure 10). Figure 9 Pull Remote Receiver Cables Out Step 15. Locate the TV IR cable and cut about five (5) inches from the end (seeFigure 6). Step 16. Twist the connector end of the new IR cable to the ends of the old IR cable and wrap securely with duct tape. Refer toFigure 7. Note: Free all cables from one another and pull them individually, as they are replaced. Figure 6 Cut Wire Ties If Provided Locate The TV IR Cable Figure 7 Twist And Tape Figure 8 Pull To Replace Step 17. Pull the TV IR cable until the new cable is out. Unwrap t...
Эта инструкция также подходит к моделям:Пульт ду - H1454 (11.03 mb)