Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Refer to the IMPORTANT SAFETY INSTRUCTIONS provided with this product and save them for future reference. Your Four-Line Speakerphone is a full-featured phone ideally suited for home-office use. It is designed to receive calls on up to four incoming telephone lines and to serve up to 16 station users. Your phone features 16 memory locations, 94 phone book memories, hold, conference call, intercom, call transfer, Caller ID display, and speakerphone capabilities. This telephone is designed to be simple to use, however, you can reach its full potential more quickly by taking a few minutes to read this user's guide. IMPORTANT: In order to use all of the features of this unit, you must subscribe to either the standard Name/Number Caller ID Service or Call Waiting Caller ID Service, To know who is calling while you are on the phone, you must subscribe to Call Waiting Caller ID Service. NOTE: FEATURES AND OPERATIONS PERTAINING TO CALLER ID DO NOT APPLY TO Model 25403.- 5 Connections & Setup Parts Checklist Make sure your package includes the following items: □ Q Base Handset Handset cord Line cords AC power supply Wall plate Modular telephone line jack Telephone Jack Requirements To use this phone, you will need an RJ11C (for a single line) or a RJ14C (for two lines) type modular phone jack, which might look like the one pictured here, installed in your home. If you don't have either modularjack, call your local phone company to find out how to get one installed. VERY IMPORTANT: In order to achieve full system operation (i.e. intercom, page, etc.), Line 1 must be connected and must be common to all phones connected to the system. Only other 25403 or 25404 models are compatible for full system operation. Connecting phones other than the 25403/25404 to Line 1 may inhibit the intercom and paging operations. For proper operation ofintercom, page function, etc, DO NOT connect a DSL modem to Line 1. To transfer a call from one station to another, the two stations should be connected to the same line. 6 Connections & Setup Base Layout NEW MESSAGE indicator (Not applicable to model 25403) 7 Connections & Setup Important Installation Information • Never install telephone wiring during a lightning storm. • Never install telephone jacks in wet locations unless thejack is specifically designed for wet locations. • Never touch non-insulated telephone wires or terminals, unless the telephone line is disconnected from the network. • Use caution when installing or modifying telephone lines. • Temporarily disconnect any equipment connected to the phone such as faxes, other phones, or modems. Important Installation Guidelines • Install telephone near both a telephone (modular) jack and an electrical power outlet. • Avoid sources of noise, such as a window by a busy street, and electrical noise, such motors, microwave ovens, and fluorescent lighting. • Avoid heat sources, such as heating air ducts, heating appliances, radiators, and direct sunlight. • Avoid areas of excessive moisture or extremely low temperature. • Avoid dusty locations. • Avoid other cordless telephones or personal computers. CAUTION: Always disconnect all phone cords from the base unit before battery installation or replacement. 8 Connections & Setup Installing the Phone The phone may be connected to two 2-line (RJ14C) wall jacks or four single line (RJ11C) walljacks to accomodate all four lines. 1. Choose an area near an electrical outlet and telephone wall jack. Your phone should be placed on a level surface, such as a table top or desk. 2. Install 3 AA-size alkaline batteries (not included) for back up power in the event of a power failure. • Use a screwdriver to loosen and lift up the battery compartment door located on the bottom of the phone. • Insert the batteries as shown on the diagram inside the battery compartment. • Snap the battery compartment door back into place and tighten the screw. NOTE: If the low battery icon appears in the display, you need to replace the batteries. It is important that you replace them as soon as possible to maintain unit operation when electrical power is off As a precaution, you may want to write down any stored information you do not want erased. IMPORTANT: If you are not going to use the telephone for more than 30 days, remove the batteries because they can leak and damage the unit. 9 Connections & Setup 3. Plug the AC power supply cord into an electrical outlet and the DC connector into the back of the base. A CAUTION: Use only the A TLINKS USA 5-2495 power supply that is compatible with this unit. Using other power supplies may damage the unit. 4. Connect the telephone line cords: If you have two dual line wall jacks installed in your home/office, plug one end of the straight telephone line cord tagged as "LINE 1+2" into the jack marked LINE 1 + 2 and one end of the other straight line cord into the otherjack on the back of the base. Plug the other end of each ...
Эта инструкция также подходит к моделям:Проводные телефоны - 25403 (369.86 kb)
Проводные телефоны - 25404 (369.86 kb)