Оценок - 4, средний балл: 2.8
(
)
)
|
Фрагмент инструкции
3. Connect a straight-through Ethernet cable from the switch to the network port labeled Network on the Cisco Unified IP Phone 6901 and 6911. Each Cisco Unified IP Phone ships with one Ethernet cable in the box. You can use either Category 3/5/5e cabling for 10-Mbps connections, but you must use Category 5/5e for 100 Mbps connections. See the “Network and Access Ports” section on page 3-2 for guidelines. 4. (Cisco Unified IP Phone 6911) Connect a straight-through Ethernet cable from another network device, such as a desktop computer, to the access port labeled Computer. Optional. You can connect another network device later if you do not connect one now. You can use either Category 3/5/5e cabling for 10-Mbps connections, but you must use Category 5/5e for 100 Mbps connections. See the “Network and Access Ports” section on page 3-2 for guidelines. 3-4 Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP) OL-20852-01 Chapter 3 Setting Up the Cisco Unified IP Phone Installing the Cisco Unified IP Phone Figure 3-1 Cisco Unified IP Phone 6901 Cable Connections 456123195792 1 Slot for Ethernet cable 4 Network port (10/100 SW) connection IEEE 802.3af power enabled 2 Handset connection 5 DC adaptor port (DC48V) 3 Slot for handset cable 6 Slot for DC adaptor cable Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP) OL-20852-01 3-5 Chapter 3 Setting Up the Cisco Unified IP Phone Installing the Cisco Unified IP Phone Figure 3-2 Cisco Unified IP Phone 6911 Cable Connections 195780234561 1 DC adaptor port (DC48V) 4 Network port (10/100 SW) connection IEEE 802.3af power enabled 2 AC-to-DC power supply (optional) 5 Access port (10/100 PC) connection 3 AC power wall plug (optional) 6 Handset connection Related Topics • Footstand, page 3-7 • Verifying the Phone Startup Process, page 3-9 • Configuring Startup Network Settings, page 3-9 3-6 Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP) OL-20852-01 Chapter 3 Setting Up the Cisco Unified IP Phone Footstand Footstand The Cisco Unified IP Phone 6901 has a foldable footstand. When the footstand is unfolded, it gives the phone an elevated viewing angle. Figure 3-3 illustrates the footstand on the Cisco Unified IP Phone 6901. Figure 3-3 Cisco Unified IP Phone 6901 277349 Figure 3-4 illustrates attaching the footstand at a higher angle on the Cisco Unified IP Phone 6911. Figure 3-4 Cisco Unified IP Phone 6911 11112222277348 1 Insert the connectors into the lower slots 2 Lift the footstand until the connectors snap into the upper slots Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP) OL-20852-01 3-7 Chapter 3 Setting Up the Cisco Unified IP Phone Footstand Higher Viewing Angle Connect the footstand to the lower slots for a higher viewing angle. 277346 Lower Viewing Angle Connect the footstand to the upper slots for a higher viewing angle. 277347 3-8 Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Communications Manager 8.0 (SCCP) OL-20852-01 Chapter 3 Setting Up the Cisco Unified IP Phone Verifying the Phone Startup Process Mounting the Phone to the Wall You can mount the Cisco Unified IP Phone 6901 on the wall by using a standard telephone wall plate with an opening for an RJ-45 connector. Cisco recommends that you use Leviton Wall Mount plate (Leviton type number: 4108W-0SP) to wall mount the Cisco Unified IP Phone 6901. For information on installing the wall mount kit for Cisco Unified IP Phone 6901, see Installing a Wall Mount for the Cisco Unified IP Phone 6901, page E-1. You can mount the Cisco Unified IP Phone 6911 on the wall by using special brackets available in a Cisco Unified IP Phone wall mount kit. For information on installing the wall mount kit, see Installing a Wall Mount for the Cisco Unified IP Phone 6911, page E-7. Note Wall mount kits are not included with the phone and must be ordered separately. Verifying the Phone Startup Process The LEDs on the MWI on the handset, and the LEDs on the Mute button light up during bootup. Upon successful completion of the bootup process, the LEDs turn off, and the phone is ready for calls. If the phone successfully boots up, it has started up properly. If the phone does not start up properly, the user receives a reorder tone. For more information, see the “Resolving Startup Problems” section on page 7-1. Configuring Startup Network Settings If you are not using DHCP in your network, you must configure these network settings on the Cisco Unified IP Phone after installing the phone on the network: • IP address • IP subnet information • Default Router • TFTP server IP address Collect this information and see the instructions in Chapter 4, “Configuring Settings on the Cisco Unified IP Phone.” Cisco Unified IP Phone 6901 and 6911 Administration Guide for Cisco Unified Comm...
Эта инструкция также подходит к моделям:Проводные телефоны - 6901 (682.97 kb)