Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
--/ Battery compartment 7 Desktop Installation 1. Plug the coiled cord into the handset. Plug the other end into the jack on the side of the base. Place the handset in the cradle on the base. 2. Plug the line cord into jack on the back of the base. Plug the other end into a wall jack. 3. Set the RINGER switch on the base to the desired loudness. • HI = Default, loudest sound. • LO = Sound will be lower. • OFF = Telephone will not ring. 8 Wall Mount Installation 1. Carefully turn the phone over. Detach the wall mount bracket from the two sets of top grooves by pressing the tabs in. Pull the bracket from the phone and turn it around so that it looks like the diagram below. Gently press the bracket into the two sets of bottom grooves until it snaps into place. 2. Plug the short line cord into the jack on the back of the base. 3. Feed the line cord through the grooves provided so that the base area is flat and ready to mount on the wall. 4. Connect the other end of the line cord into the wall phone jack. 5. Place the handset in the cradle of the base as soon as possible to hang up the phone. 6. Plug the coiled cord into the handset. Plug the other end into the jack on the side of the base. 7. Slip the mounting holes of the base (on bottom of unit) over the wall plate posts and slide the base down until the phone is firmly in place. 8. Set the RINGER switch on the base to the desired loudness. • HI = Default, loudest sound. • LO = Sound will be lower. • OFF = Telephone will not ring. 9 Setting Up the Caller ID Menu You should not plug the telephone into the wall line jack while setting up the Caller ID menu. An incoming call may invalidate the change if it was not yet saved. The phone must display xx CALLS before you can enter the setup menu. 1. Press the OPTIONS button. OPTIONS MENU A v appears. 2. At this point you can press either REVIEW up or down button to scroll among the 6 menu screens, which are: • # 1 OPTIONS MENU A v • # 2 LOCAL AREA CODE (default - - -) • # 3 LANGUAGE (default English) • # 4 (LCD) CONTRAST (default 3) • # 5 T/P DIAL MODE (default tone) • # 6 EXIT OPTIONS 3. You have 10 seconds following any key press before the phone will automatically return to the Summary Screen. OPTIONS button REVIEW Summary Screen 10 Setting Your Local Area Code The telephone uses the programmed area code to determine the number format to display when a valid Caller ID signal is received and is also used for the Dialback feature. 1. Press the OPTIONS button. OPTIONS MENU A v appears. 2. Press the REVIEW up or down buttons until LOCAL AREA CODEappears. 3. To enter and change the area code, press OPTIONS again. The display shows the present area code stored. The left-most digit or a minus sign (-) flashes, indicating it is ready to accept the area code entry. 4. Press 1-9 on the key pad for the first digit. To clear the digit, press either * or #. 5. When the desired digit is flashing, press either REVIEW button to advance to the next digit. OPTIONS button REVIEW 11 6. Repeat steps 4 and 5 until all the digits for your area code are correct. If you make a mistake, you can simply retrace the previous steps until your area code is set. 7. Press OPTIONS once again to store the area code and return to the "LOCAL AREA CODE" display. Setting the CID Display Language This adjustment changes the Caller ID prompts to be displayed in English or Spanish. 1. Press the OPTIONS button. OPTIONS MENU A v appears. 2. Press the REVIEW up button until LANGUAGE appears. 3. To enter and change the language, press the OPTIONS button. The display shows the current language. The default is English. 4. Press either REVIEW button to change the setting. 5. Press OPTIONS once again to store the setting and return to the "LANGUAGE" display. OPTIONS button REVIEW 12 Setting the Display Contrast This adjustment allows optimization of the contrast and viewing angle of the display. 1. Press the OPTIONS button. OPTIONS MENU A v appears. 2. Press the REVIEW up button until (LCD) CONTRAST appears. 3. To enter and change the contrast, press the OPTIONS button. The display shows the current contrast setting. There are 5 levels of contrast, with the default set to 3. 4. Press either REVIEW button to change the setting. 5. Press OPTIONS once again to store the setting and return to the "(LCD) CONTRAST" display. OPTIONS button REVIEW 13 Setting the Dial Mode This adjustment allows you to select tone (touch-tone) or pulse (rotary) mode dialing. 1. Press the OPTIONS button. OPTIONS MENU A v appears. 2. Press the REVIEW up button until T/P DIAL MODE appears. 3. To enter and change the dial mode, press the OPTIONS button. The display shows the current setting. The default is set to tone. 4. Press either REVIEW button to change the setting. 5. Press OPTIONS once again to store the setting and return to the "T/PDIAL MODE" display. Exiting Setup To exit the Setup menu after your chan...
Эта инструкция также подходит к моделям:Проводные телефоны - 29391 (899.89 kb)
Проводные телефоны - 29391 (899.89 kb)
Проводные телефоны - 29391 (899.89 kb)