Оценок - , средний балл:
(
)
)
Производитель: Elite Screens
Размер: 533.04 kb
Название файла: c6383bcb-12ae-48ec-a119-ec4db694ed97.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
1. Frame Parts x 6 pcs (4 Top & Bottom frame pcs + 2 Side frame pcs) 2. Tension Rods x 6 pcs (4 Top & Bottom frame rods + 2 Side rods) 3. Screen Material x 1 pc 4. Center Joints x 2 pcs 5. Elbow Joints x 4 pcs 6. Wall Brackets x 2.3 pcs (depending on size) 7. Screws x 16 pcs 8. User Guide x 1 pc 9. Center Support Bar x 1.2 pcs (depending on size) 10. Support Joiner x 2.4 pcs (depending on size) 11. Fix Plates x 30.90 pcs (depending on size) 12. Black Cloth Backing x 1 pc (AcousticPro 1080 models only) Installation Instructions Assemble the Frame 1. Insert the Center Joint Connector to the horizontal frame piece and secure with screws. Rev.051811.AS info@elitescreens.com 3 Rev.051811.AS info@elitescreens.com 2. Insert the other horizontal frame piece to the Center Joint connector and secure with screws. Note: To make sure the frame pieces line up correctly, do not tighten the screws until assembly is complete. 3. Insert both Elbow Joint connectors into the long horizontal frame (see fig. 1). Push Push Joint Long frame ( fig.1) P ush P ush S ho rt fram e S h o rt fram e 1/2Long frame Push 4 Rev.051811.AS info@elitescreens.com Push Push ( fig.2) Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles 4. Join all four frame parts together following the steps showed below (see fig. 2) 5. Make sure all four corners join correctly to form a perfect rectangle, then fasten the four angles together by using the included joint screws. (see fig. 3) Screw ( fig.3) 5 Rev.051811.AS info@elitescreens.com Tension Rod (Horizontal) x 4 Tension Rod (Vertical) x 2 Attach the Screen Material to the Frame 1. Lay out the material and Tension Rods on a clean & dry surface. Insert the Tension Rods through the sleeves according to their corresponding lengths on each edge of the screen (see fig. 4). 2. Place the screen material on the back of the frame and insert the tension rods into the grooves running of each corner of the frame. Insert the Fix Plates to the back of the frame to secure the rods into place creating tension for a flat surface (see fig. 5 & 6). Push ( fig.5) Viewing surface (Front of screen) Steel rod fix plate Steel rod Push ( fig.4) Steel rod Screen Push 6 Rev.051811.AS info@elitescreens.com Black Backing for AcousticPro1080 Models This procedure only applies to models with AcousticPro 1080 Material. The Black Backing counters the effects of light penetration that would otherwise light up all items behind the screen and spoil the picture. Attach the Black Backing behind the projection surface and secure to the Velcro.Faced Fix Plates. After the material has been installed, the backing will lie over the back of the white (AcousticPro1080) material and then be held into place by the fix plates as they are added (fig. 1.3). Interval markings reveal the suggested points of attachment (fig. 1). The prongs on the fix plates (fig.2) straddle a lip on the back of the frame creating a friction to hold the material in place (fig.3.4). Fig.1 Fig.2 *An alternate way to attach the black backing to the back of the AcousticPro1080 material is to utilize the Velcro tabs located on the outer surface of the fix plates (fig.3.4) Black backing Fix plate secures AcousticPro1080 material and the black backing behind it. AcousticPro1080 Screen Material Cover by Black backing Fix Plate Black backing Tension Rod (stretches the AcousticPro1080 material) Fig. 3 Fig. 4 Attach the Fix Plates 1. Make sure that the material and frame are both lying face down on a clean, dry and non.abrasive surface. 2. Center the material inside of the frame Note: The material was made smaller than the frame in order to be stretched to create a sufficient amount of tension. 3. Start attaching the Fix Plates in the center of each horizontal frame piece (1), then in the center of each vertical frame piece (2). (see fig.7) Note: Follow these instructions to make sure the material is properly fixed in the center position of the frame. After attaching the fix plates in sequence #2 (vertical sides), remove the fix plates in sequence #1 (horizontal pieces) and re.attach them again, and also remove the fix plates from sequence # 2, and re.attach. 4. Follow the suggested numbers 3.8 to properly attach the fix plates to the frame. (Fig. 7) Center Support Bar 1. Insert the Support Joiner into each side of the Center Support Bar. SupportJoinerCenterSupportBar 2. Insert the Center Support Bar into the upper top groove of the back frame (not the fix plates insert) with the bottom end near the approximate center point of the frame and place it in at an angle so that both ends of the bar are in alignment with the groove (see fig.8). Rev.051811.AS info@elitescreens.com 3. Slide the top end of the bar into the top center point location to complete the installation. ...