Войти:
Оценок - 5, средний балл: 4.2 ( )

Инструкция по эксплуатации Omnimount, модель PMD.5

Производитель: Omnimount
Размер: 353.1 kb
Название файла: 7fc59703-0bdb-419e-bb62-268186c2b016.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Every effort has been made to provide accurate and error- free assembly and installation. OmniMount Systems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions. If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise from the inability to use this product safely, properly, and in the manner for which it has been designed and manufactured. Warranty does not apply to products which have been lost, damaged by misuse, abuse, or accident. OmniMount Systems, Inc. 8201 South 48th Street • Phoenix, AZ 85044-5355 1-800-MOUNT-IT • P/ N 1002082—Rev. D 9/ 2004 Installation Instructions PMD.5 — PMD1— PMD2: Universal Projector Mounts Universal Mounting Grid Superior Mounting Flexibility Adjustable Ceiling Pipe Drop IMPORTANT: To utilize the PMD projector mount, the projector must have mounting lands ( threaded inserts) on the base. Contact OmniMount if you have any questions regarding the proper installation of this projector mount system. Questions? 1-800-MOUNT IT Models: PMD.5 — PMD1 — PMD2 Step 5 Slide the bottom projector mounting plate onto the previously installed top projector mounting plate. (Fig. 11) Note: Make sure that the cables don’t get pinched while sliding the plates together. Fig. 11 Fig. 12 Important: Always secure projector plates by installing 3/ 8” screws ( G) into holes on front edge of plates. Additional security can be provided by installing small padlocks through security slots at the rear of the projector plates. (Fig. 12) Attach cables to the projector. Turn projector ON, and make pitch and keystone adjustments as per the projector manufacturers instructions. For additional pitch/ tilt, use the three adjustment knobs on top of the PMD mount (Fig. 13). Fig. 13 Part Description Qty. Mount Assembly Hard- ware A Top Projector Plate 1 B Bottom Projector Plate 1 C Pipe Drop Assembly 1 D Plastic Cover 1 E Ceiling Plate 1 Bag F Hex Screw: .”-20 X .” 1 (d) G Screw: .”-20 X 3/ 8” 2 (c) H Hex Screw: .”- X 5/8” 4 (d) I Hex Screw: .”- X .” 6 (d) J Lag Bolt: 5/16” X 3” 4 (e) K Plastic Plugs 14 (b) Hex Wrench 1 (d) 7 Step 5 Fig. 6 Determine required mounting screw size ( 4, 5 or 6 mm) for projector. Note: Consult projectors owners’ manual for screw sizes and mounting holes. Lay projector on table with mounting surface face up. Place grid section of bottom projector mounting plate onto top of projector in desired mounting orientation (horizontal or vertical). (Fig. 6) Using a pencil or felt tipped pen, mark the locations of the projectors threaded inserts onto the grid for refer- Part Projector Mounting Hardware Qty. Bag Hardware Bags 1 Large Washer 8 (a) 2 Metal Spacer: 3/ 8” 4 (a) 3 Plastic Spacer: 1” 1 (b) PMD–.5 /PMD–1 PMD- 2 4 Screw: 5mm x 25mm Screw: 6mm x 25mm 4 (c) 5 Scre...

Эта инструкция также подходит к моделям:
Проекторы - PMD1 (353.1 kb)
Проекторы - PMD2 (353.1 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории