Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
(16) Lens : Projects expanded image. Names l Control panel Remote Control (9) (5) (10) (1) (2) (8) (7) (6) (4) (3) (12) (6) (11) (2) (8) (17) (15) (16) (4) (3) (7) (17) (13) (14) (1) Name : Main Function Control panel (1) ENTER button (2) MENU button (3) KEYSTONE button (4) ON/STANDBY button (5) ON/STANDBY indicator (6) INPUT button (7) RETURN button (8) Selection button (9) LAMP indicator ( 10) TEMP indicator Remote control (1) ENTER button (2) MENU button (3) KEYSTONE button (4) ON/STANDBY button (6) INPUT button (7) RETURN button (8) Selection button : Accepts the selected mode. : Displays menus. p.34 : Adjusts keystone distortion. p.27 : Turns the power on/off (standby). p.23 : Displays whether power is on or off (standby). p.23 : Selects input. p.25 : Goes back one screen. : Menu selections and adjustments, volume control, etc. p.34 : Informs the abnormality of lamp. p.48 : Informs the abnormality of internal temperature. p.48 : Accepts the selected mode. : Displays menus. p.34 : Adjusts keystone distortion. p.27 : Turns the power on/off (standby). p.23 : Selects input. p.25 : Goes back one screen. : Menu selections and adjustments, volume control, etc. p.34 16 Name : Main Function ( 11)AUTO SET button : Sets up input from p.27 ( 12) MUTE button : Cuts off the picture and p.29 ( 13) FREEZE button : Pauses image. p.30 ( 14)Ten-Key button : Use when entering password. Remote control button Input items Remote control button Input items 1 [1] 7 [7] 2 [2] 8 [8] 3 [3] 9 [9] 4 [4] 0 [0] 5 [5] Deletes one character. 6 [6] ( 15) PICTURE button : Changes image mode. p.29 ( 16) SCREEN SIZE button : Changes screen size. p.30 ( 17) RESIZE button : Enlarges image. p.28 Note •For the remainder of this manual, buttons are referred to as follows: Selection buttons . ; ENTER button . Preparations 17 18 19 Preparations ¦ Operating the remote control Point toward the projector’s infrared remote sensor, and press a button on the remote control. • Operating the projector from the front Approx. 15° Approx. 5m ¦ Loading dry-cell batteries into the remote control q Remove the battery cover. w Insert the dry-cell batteries. Be sure to align the plus and minus ends of the batteries properly. e Replace the battery cover. Dry-cell batteries • Before using the batteries, be sure to observe the Safety Precautions described in previous pages. • Remove batteries from remote control when not using for extended periods. • If the remote control stops working, or if its range decreases, replace all the batteries with new ones. The remote control • The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting. • Do not drop or bang. • Do not leave in hot or humid locations. • Do not get wet or place on top of wet objects. • Do not take apart. • In rare cases, ambient conditions could impede the operation of the remote control. If this happens, point the remote control at the main unit again, and repeat the operation. Preparing and using the remote control When operating the remote control from behind the projector, the light is reflected on the projecting surface and may travel a shorter distance to reach the projector depending on the shape and material of the projecting surface. Names of the terminals on the rear panel (1) (2) (3) (4) (6) (8) (9) (5) (7) COMPUTER 2 IN (Y/PB/PR 2) /MONITOR OUT Name : Main Function (1) CONTROL terminal : When operating the projector via a computer, connect this to the controlling computer’s RS-232C port. p.53 (2) AUDIO (L/R) terminal : Input audio signals from video equipment. (3) VIDEO terminal : Input video signals from video equipment. (4) S-VIDEO terminal : Input S video signals from video equipment. (5) AUDIO IN terminal : Input audio signals from a computer, or from video equipment with a component video signal output terminal. (6) COMPUTER 1 IN terminal : Input RGB signal from a computer or other source or a component video signal (Y/PB/PR) from video equipment. (7) AUDIO OUT terminal : Outputs audio signals. (8) COMPUTER 2 IN terminal : Inputs RGB signal from a computer or other source or (Also used for MONITOR OUT terminal) a component video signal (Y/PB/PR) rom video equipment. It can also be used as MONITOR OUT terminal by the switch of (9). (9) Switch : Switches between COMPUTER 2 IN and MONITOR OUT. 20 21 Preparations p.53 Video recorder, DVD player, etc. To audio output White (L)/Red (R) S-video cable (not supplied) To S-video output Before connection • Read the owner’s manual of the device you are connecting to the projector. • Some types of computer cannot be used or connected to this projector. Check for an RGB output terminal, supported signal p.51 , etc. • Turn off the power of both devices before connecting. • The figure is a sample connection. This does not mean that all of these devices can or must be connected simultaneously. (Dotted lines mean items can be exchanged.) Connection Computer (for control) Computer To RS-232C t...
Эта инструкция также подходит к моделям:Проекторы - TLP-XD2000U (6.15 mb)