Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Enter a 4-digit number as the Network PIN code onto the text box and click Set button. The projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. This is to perform the login authentication firmly. The default Network PIN code [0000] means no Network PIN code is set. . When you connect the projector to the network, it is recommended to set a new Network PIN code. Only a four-digit number is valid for the Network PIN code. PJLink and password setting This is to set the PJLink password authentication on or off. If set "ON" with the PJLink pull- down menu, the password must be required. Enter a password* onto the text box and click Set button. . 1 to 32 alphanumeric characters can be used for the password. What's PJLink? The projectors equipped with PJLink function can be used together on the same network, regardless of model or brand, for centralized control and monitoring. This standard was established by the Japan Business Machine and Information System Industries Association (JBMIA). Please visit the Website at PJLink Notice The projector is compliant with PJLink Standard Class 1 of JBMIA, and it supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. Projector Input PJLink Input Parameter COMPUTER 1 ANALOG PC RGB 2 12 COMPONENT RGB 3 13 S-VIDEO RGB 4 14 SCART RGB 5 15 COMPUTER 2 ANALOG PC RGB 1 11 VIDEO VIDEO VIDEO 2 22 Network configuration Click Network on the main menu. The following setting page is displayed. The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) and projector name are set up on this menu. The IP address and Subnet Mask have been configured already in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. Item Description LAN mode.............Displays the selected LAN mode DHCP..........................Sets DHCP configuration (ON/OFF). IP address..............Sets IP address of the projector Subnet mask........Sets Subnet mask according to your network environment. Default gateway*1......Sets IP address of the default gateway (Router) DNS*2........................ Sets IP address of the DNS server. Must be set when using the e-mail function Projector name*3.. Sets name of the projector. (64 characters maximum) . You must use the number specified by your administrator. The address must be entered as a group with four numbers split by a dot like [192.168.001.101]. *1 Set [0.0.0.0] if the network does not provide the gateway (router). *2 Set [0.0.0.0] if you do not use the function E-Mail alert. *3 If you use the DNS server, register the host name registered to the DNS server as a projector name. You can access with this projector name from any computers in your network. If you do not use the DNS server, access with the assigned IP address to the projector. * All the network setting will reset to the default when setting [0.0.0.0] of the IP Address. * If you make incorrect settings, you cannot find out the new network settings. Be careful to set up them correctly, otherwise you cannot connect to the projector. It is recommended to make a note of them. E-mail setting E-mail setting This projector has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and follow the below steps. Item Description SMTP server............................ Enter server name or IP address of the SMTP server. (up to 60 characters) SMTP server port ................ Enter Port number of the SMTP server. (from 1 to 65535) Administrator address.....Enter e-mail address of administrator. Add address............................ Enter e-mail address of the user to send mail when the projector has an abnormality. Auth ............................................. Sets authentication setting option. (Off, SMTP Auth, POP before SMTP) SMTP Auth ............................... Sets user authentication setting option when selecting "SMTP Auth" in above column. (CRAM-MD5, LOGIN, PLAIN) User ID ........................................ Enter SMTP user ID. (up to 63 characters) Password .................................. Enter SMTP password. (up to 63 characters) POP server................................ Enter server name or IP address of the POP server. (up to 60 characters) POP server port ................... Enter Port number of the POP server. (from 1 to 65535) SMTP Authentication setting 1 Setting SMTP server and administrator address Enter the server name or IP address of the SMTP server*1, the port number of the SMTP server and administrator address and click Set button. ...
Эта инструкция также подходит к моделям:Проекторы - LV-7290 (4.56 mb)
Проекторы - LV-7295 (4.56 mb)
Проекторы - LV-7390 (4.56 mb)