Оценок - 2, средний балл: 4.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
For best operating performance, replace the lamp according to the usage time. You can view the lamp usage time in the Information Display (INFO button). • Use the recommended lamp when replacing. Replace the lamp with the one specified below. - Lamp Model Name : NSHA230SS - Lamp Manufacturer : Ushio - For inquiries on lamp purchase, please refer to 'Contact SAMSUNG WORLDWIDE'. • Check that the power cord is unplugged before replacing the lamp. • Because the lamp is a high temperature and high voltage product, wait at least one hour from the time you disconnect the power cord before replacing the lamp. • The lamp is located on the left side of the projector (when looking from the front). • Do not leave the old lamp near inflammables or in reach of children. There is a danger of burn or injury. • Remove dirt or foreign material around or inside the lamp unit using a proper vacuum device. • When handling the lamp, avoid touching any part of it except for the handles. If you handle the lamp incorrectly, you can shorten the lamp's lifetime and affect picture quality. • When you turn the projector over to change the lamp, put the projector on a soft cloth on a flat surface. • The projector has been designed so that the projector does not work if the lamp cover is not completely assembled after a lamp replacement. If the projector does not work properly, please check the operating status of the indicator LED. Lamp contains Mercury. Dispose According to Local, State or Federal Laws. Lamp Replacement Procedure □ Since the lamp is a high temperature and high voltage product, wait at least one hour from the time that the power cord is disconnected before replacing it. The lamp is located on the left side of the projector (when looking from the front). 1. Remove the screw shown in the figure below and than open the cover. 2. Remove the two (2) screws shown in the figure below. 2-6 Installation and Connection 3. Hold and pull the lamp handle out of the projector, as shown in the figure below. Replacing and Cleaning the Filter Precautions when replacing the projector filter: • The filter is located at the bottom of the projector. • Turn off the power of the projector, and then disconnect the power cord after the projector has cooled sufficiently. Otherwise, its parts may be damaged due to internal heat. • When you replace the filter, you may release some dust. • For inquiries on filter purchase, please refer to 'Contact SAMSUNG WORLDWIDE'. The sequence for replacing or cleaning the filter of the projector. 1. Turn off the power of the projector, and then disconnect the power cord after the projector has cooled sufficiently. 2. Turn the projector over so that its bottom points upward, and then push and remove the filter cover in the direction of the arrow. * When placing the projector with the bottom facing up, make sure to place a soft cloth under the projector to prevent scratches. C 1 . . \_/ 3. Replace or clean the filter. • When cleaning the filter, use a small vacuum cleaner designed for computers and small electronics products, or wash it under Installation and Connection 2-6 running water. • After washing the filter under running water, make sure to dry it completely. The moisture may cause the filter to corrode. • If dust cannot be separated from the filter or the filter is torn, it must be replaced. • Make sure to select the Reset Filter Time option after replacing or cleaning the filter of the projector Ventilation openings The location of the ventilation openings: • The ventilation openings are located on the right and left sides and at the bottom of the projector. 2-6 Installation and Connection 2-7 Rear Side 1. PC IN port 7. AUDIO OUT port 2. PC/DVI AUDIO IN port 8. [AV IN] R-AUDIO-L port 3. HDMI/DVI IN port 9. [AV IN] VIDEO Input port 4. Remote Control Signal Receiver 10. [AV IN] S-VIDEO port 5. RS-232C port (For service only) 11. Kensington Lock 6. PC OUT port 12. POWER Input port Installation and Connection 2-7 2-8 Setting up the PC Environment Check the following items before connecting your PC to your projector. 1. Click the right mouse button on the Windows desktop, and then click [Properties]. The
Проекторы - SP-L221 (1.5 mb)
Проекторы - SP-L251 (1.5 mb)