|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Resets the value of an item to its factory preset value or returns the enlarged image to its original size. This key functions when the menu or a setting item is displayed on the screen. n D ZOOM +/– key Enlarges the image at a desired location on the screen. o Arrow keys (M/m/,) p MENU/TAB key Functions as a MENU key. q APA (Auto Pixel Alignment) key Automatically adjusts a picture to its clearest while a signal is input from a computer. For details, see “Smart APA” in the SET SETTING menu on page 34. r VOLUME +/– keys s LENS key This function is not provided in this projector. t PJ/NETWORK (Projector/ Network) selector switch Set this switch to PJ always. u COMMAND ON/OFF switch When this switch is set to OFF, no key on the Remote Commander function. This saves the battery power. v Infrared transmitter Location and Function of Controls Battery installation 1 Push and slide to open the lid, then install the two size AA (R6) batteries (supplied) with the correct polarity. While pressing the lid, slide it. Be sure to install the battery from the # side. 2 Replace the lid. Notes on batteries • Make sure that the battery orientation is correct when inserting batteries. • Do not mix an old battery with a new one or different types of batteries. • If you will not use the Remote Commander for a long time, remove the batteries to avoid damage from battery leakage. If batteries have leaked, remove them, wipe and dry the battery compartment, and replace the batteries with new ones. Notes on Remote Commander operation • Make sure that nothing to obstruct the infrared beam between the Remote Commander and the remote control detector on the projector. • The operation range is limited. The shorter the distance between the Remote Commander and the projector is, the wider the angle within which the commander can control the projector. Overview Location and Function of Controls 15 B Setting Up and Projecting Installing the Projector This section describes how to install the projector. Distance between the screen and the center of the lens The distance between the lens and the screen varies depending on the size of the screen. Use the following table as a guide. Unit: m (ft) Screen size (inches) 40 60 80 100 120 150 200 300 Minimum 1.5 2.3 3.0 3.8 4.6 5.8 7.7 11.6 Distance (4.9) (7.5) (10.0) (12.5) (15.0) (19.0) (25.2) (37.9) Maximum 1.9 2.9 3.84.85.8 7.2 9.7 14.5 Distance (6.2) (9.5) (12.5) (15.7) (19.0) (23.6) (31.7) (47.6) Note For details on ceiling installation, consult with qualified Sony personnel. Installing the Projector Connecting the Projector When you connect the projector, make sure to: • Turn off all equipment before making any connections. • Use the proper cables for each connection. • Insert the cable plugs firmly; loose connections may increase noise and reduce performance of picture signals. When pulling out a cable, be sure to pull it out from the plug, not the cable itself. To connect the projector, refer to the illustrations on the next and the following pages. Connecting with a Computer This section describes how to connect the projector to a computer. For more information, refer to the computer’s instruction manual. Notes • The projector accepts VGA, SVGA, XGA, SXGA, SXGA+ and UXGA (60 Hz) signals. However, we recommend that you set the output mode of your computer to XGA mode for the external monitor. • If you set your computer, such as a notebook type, to output the signal to both your computer’s display and the external monitor, the picture of the projector may not appear properly. Set your computer to output the signal to only the external monitor. For details, refer to the computer’s operating instructions supplied with your computer. • This projector is compatible with a DDC2B (Digital Data Channel 2B). If your computer is compatible with a DDC, turn the projector on according to the following procedures. 1 Connect the projector to the computer by using the supplied HD D-sub 15-pin cable or DVI cable. 2 Turn the projector on. 3 Start the computer. Setting Up and Projecting Connecting the Projector 17 To connect a computer When you use a wireless mouse INPUT D OUTPUT INPUT A INPUT B INPUT C NETWORK (PLUG IN POWER) (MONO) L R RS-232C IN S VIDEO VIDEO AUDIO RGB AUDIO RGB DVI-D R/R-Y/Pn G/Y B/B-Y/Ps SYNC/HD VD AUDIO MONITOR AUDIO AUDIO CONTROL REMOTE VIDEO INCONTROL S to USB connector Right side USB cable (supplied) (Connect the USB cable to use a wireless mouse.) to monitor output Computer HD D-sub 15-pin cable (supplied) to audio output a) Use a no-resistance cable. b) Connect a DVI cable to use a DVI equipment. DVI cable (not supplied)b) To DVI-D output Stereo audio connecting cable (not supplied)a) On the USB function When connecting the projector to a computer by using the USB cable for the first time, the computer recognizes the following devices automatically. USB human interface device (wireless mouse function) Recommended operating environment When you use the USB function, connect your c...