Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
BBe especially careful not to let young children look into the lens. In addition, turn off the power when you are away from the projector. Do not place your hands or other objects close to the air outlet port. BHeated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result. Replacement of the lamp unit should only be carried out by a qualified technician. BThe lamp unit has high internal pressure. If improperly handled, explosion might result. BThe lamp unit can easily become damaged if struck against hard objects or dropped, and injury or malfunctions may result. When replacing the lamp, allow it to cool for at least one hour before handling it. BThe lamp cover gets very hot, and contact with it can cause burns. Before replacing the lamp, be sure to unplug the power cord from power outlet. BElectric shocks or explosions can result if this is not done. Caution Do not cover the air inlet or the air outlet. BDoing so may cause the projector to overheat, which damage to the projector. BDo not place the projector in narrow, badly ventilated closets or bookshelves. BDo not place the projector on cloth or papers, drawn into the air inlet port. Do not set up the projector in humid the projector may come into contact BUsing the projector under such shocks. When disconnecting the BIf the power cord itself short-circuits or serious Always disconnect BMoving the which could ENGLISH-7 Preparation Do not place any heavy objects on top of the projector. Accessories BFailure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury. Check that all of the accessories shown below have been included with your projector. Do not short-circuit, heat or disassemble the batteries or place them into water or fire. BFailure to observe this may cause the batteries to overheat, leak, explode or catch fire, and burns or other injury may result. When inserting the batteries, make sure the polarities (+ and -) are correct. BIf the batteries are inserted incorrectly, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result. Use only the specified batteries. BIf incorrect batteries are used, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result. Insulate the battery using tape or similar before disposal. BIf the battery comes into contact with metallic objects or other batteries, it may catch fire or explode. Do not put your weight on this projector. BYou could fall or the projector could break, and injury may result. BBe especially careful not to let young children climb onto the projector. Disconnect the power cord plug from the wall outlet as a safety precaution before carrying out any cleaning. BElectric shocks can result if this is not done. Ask an Authorised Service Center to clean inside the projector once a year. BIf dust is left to build up inside the projector without being can result in fire or problems with operation. BIt is a good idea to clean the inside of the projector humid weather arrives. Ask your nearest Authorised clean the projector when required. Please discuss Service Center regarding cleaning costs. We are constantly making efforts to environment. Please take non repairable recycling company. Card remote control unit (TNQE239 x1) ENTER AUTO SETUP VIDEO INPUTPOWER RGB MENU Lithium battery for remote control unit (CR2025 x1) RGB signal cable [3.0 m (9.10.), K1HA15FA0002 x1] Video/Audio cable [3.0 Power cord FREEZE SHUTTER m (9.10.), (TXFSX01PSZZ x 1) INDEX WINDOW VOLUME D.ZOOM STD K2KA2FA00002 x 1] PROJECTOR Carrying bag (TPEP009 x1) Preparation NOTICE: BThis product has a High small amount of mercury. Disposal of these materials environmental considerations. please contact Alliance: < 8-ENGLISH ENGLISH-9 Before use Cautions when moving the projector Be sure to attach the lens cover before moving the projector. The projection lens is extremely susceptible to vibration and shocks. When moving the projector, use the accessory carrying bag. When placing the projector inside the carrying bag, position it so that the lens is facing upward. Cautions regarding setting-up Avoid setting up in places which are subject to vibration or shocks. The internal parts can be damaged, which may cause malfunctions or accidents. Do not set up the projector near high-voltage power lines or near motors. The projector may be subject to electromagnetic interference. If installing the projector to the ceiling, ask a qualified technician to carry out all installation work. You will need to purchase the separate installation kit (Model No.ET-PKC80). Furthermore, all installation work should only be carried out by a qualified technician. If using this projector at high elevations (above 1400 set the FAN CONTROL to HIGH. (Refer to page Failure to observe this...