Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Remove enough drawers to reach the top back inside of the unit. (See Drawer installation and removal.) • Push actuator rod to back of unit to disconnect from back of lock. Move actuator rod for access. • Remove (4) screws holding top in place. • Lift top off of unit enough to reach the wiring harness. • Disconnect wiring harness from unit. • Remove top from unit. Press to release Chest Top Installation • Connect wiring harness to top. • Position top on unit. • Attach using (4) screws. • Make sure the back of the actuator rod is inserted into the actuator rod holder in the back of the unit. • Push actuator rod toward back of unit and line up with lock. Insert the actuator rod into the back of the lock. • Test lock operation. • Reinstall drawers. • Reconnect power to the unit. Disconnect actuator rod 2 INFORMATION CENTER INSTALLATION FAClA INSTALLATION AND REMOVAL AND REMOVAL Tools Required: Tools Required: Screwdriver, Crosstip Tape 3/8" Wrench drill 5/32" drill bit Rivet gun Removal Installation Pliers • Disconnect power from the unit. • Remove enough drawers to reach the • Plug in • Position information information center. center in unit. To remove facia Rivet retaining screw under the information • Tighten retaining screw enough to • Remove enough drawers to reach the center. (See removing and installing hold information center in place. Do top back inside of the chest. Connector drawers.) not overtighten. • Remove lock. (See lock installation • Loosen (do not remove) the retaining • Reinstall drawers. (See Removing and removal.) screw under the information • Pull the information center center. straight out and installing drawers.) • Reconnect power to unit. • Remove chest top. See installation and removal. chest top to remove. • Set information center as desired. • Carefully drill out (2) rivets holding Note: Tape unplugging wire to unit before the information center. This (See information center operation.) facia to • Remove chest. facia. will the prevent unit. the wire from retracting into To reinstall facia Front • Unplug the information center. • Position facia on unit. Make sure connector is on top of chest. • Attach using (2) rivets supplied. Tape wire in Press to • Reinstall lock, chest top, and drawers. place before release disconnectin( LOCK INSTALLATION AND REMOVAL LOCK INSTALLATION AND REMOVAL Lock To remove lock • Remove enough drawers to reach the Actuator rod lock retaining clip behind the lock. holder • Remove lock retaining clip. Pull lock out to remove. To reinstall lock • Position lock in unit. Install retaining 'Lock clip to hold lock in place. • Make sure the back of the actuator rod is inserted into the actuator rod retaining clip Loosen holder in the back of the unit. retaining screw • Push actuator rod toward back of unit and line up with lock. insert the actuator rod into the back of the lock. • Test lock operation. • Reinstall drawers. 34 CONNECTING POWER • Ensure that the unit and power cord are clean and dry. • insert the round end of the power cord connector into the jack in the back of the unit. • Plug the cord into an appropriate electrical outlet. Fuse block Jack Cord REMOVING AND INSTALLING DRAWERS: • Empty the drawer. • Fully extend the drawer. Release Lever Style -Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops.) Pull out to remove. Tab Style -Depress the release tabs on both sides, (this allows the slides to ride over the stops.) Pull out to remove. To reinstall, carefully align the slides and push the drawer into the unit until the drawer stops. INFORMATION CENTER OPERATION The information center is equipped with a battery backup to maintain memory only. The display will not function while power is disconnected from the unit. Outside temperature display requires optional outside temperature sensor. Display backlight • Pressing _ turns the display backlight on for 15 seconds. Setting the current time • Press and hold _ for at least two seconds. (Second resets to zero and hour begins to flash.) • Press _ to set am/pm or 24 hour mode as desired. Note: The am/pm indicator is not shown in 24 hour mode. • Adjust hour using (_ and (_. • Pressing _ toggles to next field. Note: To toggle to minute without changing hour, press _) then (_ then • Adjust minute using (_ and (_. • Press _ to toggle to next field. • Repeat to adjust Month, Day, and Year. • Toggling past year exits set mode. • Day of week is displayed according to Month, Day, and Year. 5 Temperature Display Pressing _ toggles inside and outside temperature displays between Celsius and Fahrenheit. • Pressing _ toggles inside and outside temperature displays between ACT (Actual temperature) MIN (Minimum recorded temperature since last reset) MAX (Maximum recorded temperature since last reset) • Press and hold _ for at least two seconds to clear inside and outside minimum and maximum recorded temperatures. • An audible beep will sound when temperatu...
Эта инструкция также подходит к моделям:Прочие инструменты - AXS 706.59669 (815.72 kb)