Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
unit the and line up with lock. Insert • Remove (4) screws holding top in the lock rod into the back of the lock. Chain place. • Test lock operation. Lever Style -Lift or • Lift top off of unit enough to reach the • Reinstall drawers. lower (depending on the wiring harness. slide) the release lever • Reinstall work surface. • Disconnect wiring harness from unit. • Reconnect power to the unit. on both sides, (this allows the slides to ride • Remove top from unit. over the stops.) Pull out to remove. Tab Style -Depress the release tabs on both Lock sides, (this allows the Press to slides to ride over the release stops.) Pull out to Installation remove. • To reinstall, carefully align the slides and push the work surface into the unit • To reinstall, carefully align the slides and push the drawer into the unit until until the work surface stops. • Depress release tabs in back corners the drawer stops. of the extendable work surface. • Push the work surface into the unit to the fully retracted position. • Extend work surface far enough to gain access to connections in back. • Connect chain inside back of roll retaining away. (insert chain into the large clip round part of the slot. Slide chain to small end of slot.) Lock rod • insert retaining clip to hold chain in Remove holder place. PULL OUT WORK SURFACE WITH Lock rod screws • Plug work surface cord into back of roll-away. TASK LIGHT Removal • Reconnect power to the unit. (See: • Disconnect the power from the unit. Connecting power.) • Remove enough drawers to gain • Check work surface and task lighting access to connections in the back of for proper operation. the roll-away behind the work surface. • Reinstall drawers. 3 4 I CRAFTSMAN°I CHEST TOP WITHOUT TASK LIGHT Tools Required: Screwdriver, Crosstip Chest top removal Chest top installation • Disconnect power from unit. • Position top on unit. Attach using (4) • Remove pull out work surface. (See screws. drawer installation and removal.) • Position lock in unit. Install retaining • Remove enough drawers to reach the clip to hold lock in place. top back inside of the unit. (See • Make sure the back of the lock rod is Drawer installation and removal.) inserted into the lock rod holder in the • Remove lock retaining clip. Pull lock back of the unit. out to remove. • Push the lock rod toward the back of • Remove (4) screws holding top in unit the and line up with lock. Insert place. the lock rod into the back of the lock. • Remove top from unit. • Test lock operation. • Reinstall drawers. • Reconnect power to the unit. Lock Lock retaining clip Lock Remove holder Lock rod screws Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA F1616 DRAWERINSTALLATION AND REMOVAL • Empty the drawer. • Fully extend the drawer. Release Lever Style -Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops.) Pull out to remove. Tab Style -Depress the release tabs on both sides, (this allows the slides to ride over the stops.) Pull out to remove. • To reinstall, carefully align the slides and push the drawer into the unit until the drawer stops. I CRAFTSMAN°I TASK LIGHT REPLACEMENT Tools Required: Screwdriver, Crosstip Removal Installation • Disconnect power from the unit. • Plug in new light. • Fully extend task light assembly. • Position new light in unit in same • Make note of light orientation. orientation as original light. • Remove (6) mounting screws to • Fasten new light in place with (6) new remove light. mounting screws. • Unplug light. • Reconnect power to unit. Press to Mounting screws F1617 I CRAFTSMAN°I LOCKING SYSTEM Parts Replacement Actuator Channel Actuator Rod Bracket Actuator rod Lockbar Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA F1618 ACTUATOR ROD AND ACTUATOR ACTUATOR ROD AND ACTUATOR CHANNEL REMOVAL • Disconnect power from the unit. • Remove work surface (Roll-away only). • Remove pull out work surface (Rollaway only.) See drawer and work surface installation and removal.) • Remove enough drawers to reach the top back inside of the unit, (See drawer and work surface installation and removal.) • Push actuator rod to back of unit to disconnect from back of lock. • Rotate actuator rod straight down. • Pull out to remove. ACTUATOR CHANNEL REMOVAL • Move actuator channel fully to the right to remove from mounting flanges. Remove lock bar through top of unit Move actuator channel fully to right to remove CHANNEL REPLACEMENT ACTUATOR CHANNEL INSTALLATION. • Install slot in actuator channel over pin on lock bar. Move actuator channel fully to the right. • Insert top flanges on actuator channel into mounting flanges on inside top of unit. ACTUATOR ROD INSTALLATION • Insert actuator rod into hole in actuator channel as shown. • Insert back of actuator rod into actuator rod holder in top back of unit. • Push actuator rod toward back of unit and line up with lock. Insert actuator rod into back of lock. • Test lock operation. • Reinstall drawe...
Эта инструкция также подходит к моделям:Прочие инструменты - AXS 706.59668 (815.72 kb)