Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
earthing terminal .................. safety alert symbol English 3 582429-00/D25500 etc 1/29/03 9:29 AM Page 4 English MODEL D25550 ALB a. Tool Holder b. Depth Rod c. Side Handle d. Clamp Knob e. Alternate Side Handle Location f. Trigger Switch g. Speed Dial h. Mode Selector i. Locking Sleeve j. Retaining Pin Button k. Depth Rod Clamp Nut l. Steel Ring m. Service LED C D E F G J K M A MODEL D25500 L B C D E F G H I K M SAVE THESE INSTRUCTIONS FUTURE USE Motor Your tool is powered by a DEWALT built motor designed to be used with alternating current. Voltage decrease of more than 10% will cause loss of power and overheating. All DEWALT tools are factory tested; if this tool does not operate, check the power supply. Side Handle and Depth Rod For operating convenience, the side handle can be installed rear positions. Always operate the tool with the side handle properly assembled to maximize control of the tool. TO MOUNT IN FRONT POSITION (FIG. 1) 1. Unscrew the side handle and disassemble the side handle clamp. 2. Snap the steel ring over the collar behind the tool holder. Squeeze both ends together, mount the bushing and insert the pin. 3. Place the side handle clamp and screw on the clamp knob. Do not tighten. 4. Insert adjustable depth rod into hole. 5. Screw the side handle into the clamp knob and tighten it. 6. Rotate the side handle mounting assembly to the desired position. For drilling horizontally with a heavy drill bit, place the side handle assembly at an angle of approximately 20° to the tool for optimum control. 7. Lock the side handle mounting assembly in place by tightening the clamp knob. TO MOUNT IN REAR POSITION (FIG. 2) 1. Unscrew the side handle and remove it from the front position. 4 582429-00/D25500 etc 1/29/03 9:29 AM Page 5 Leave the side handle mounting assembly in front position so that the depth adjustment rod can still be used. 2. Screw the side handle directly into one of the rear side handle positions on either side of the tool. TO ADJUST THE DEPTH ROD 1. Insert bit into tool holder and loosen depth rod clamp 2. Place drill bit onto a surface, adjust the rod to desired depth Using the depth rod will allow you to drill a hole the depth distance between the bit and the depth rod tip. 3. Tighten clamp nut. NOTE: This adjustment can be made with or without side handle in place. Inserting and Removing Spline Drive Accessories FIG. 3: (D25550, D25551, D25650, D25850) TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. 1. Unlock the tool holder by pushing the retaining pin button (J) and holding it in. 2. Insert the bit shank into the tool holder as far as it will go. FIG. 3 started with the drill bit in an existing hole. Torque Limiting Clutch and cannot be adjusted. (Fig. 5) FIG. 4 5 3. Release the retaining pin button. 4. Pull on the bit to be sure that it is properly 5. To remove a bit unlock the tool holder as described Inserting and Removing SDS-maxAccessories FIG. 4: (D25500, D25600, D25830) TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. 1. Pull back the tool holder locking sleeve (A) and insert the 2. Turn the bit slightly until the sleeve snaps back in positio...
Эта инструкция также подходит к моделям:Прочие инструменты - 582429-00 (323.42 kb)
Прочие инструменты - D25500 (323.42 kb)
Прочие инструменты - D25550 (323.42 kb)
Прочие инструменты - D25551 (323.42 kb)