Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
Vibntion is generally a warning of trouble. 18. When cleaning, repairing or inspecting, make cerain all moving parts have stopped. Disconnect the spark pi jg wire and keep the wire away from the plug to prevent accidental starting. A CUSTOMER RESPONSIBILITIES 1. Do not operate your splitter in poor mechanical condition or when in need of repair. 2. Periodically check that all nuts, bolts, screws, hose!clamps and hydraulic fittings are tight to be sure equipmeijt is in safe working condition. Where appropriate, check all sifety guards and shields to be sure they are in the proper position. Never operate your splitter with safety guards, shields c r other protective features removed. These safety devices ire for your protection. 3. Replace all damaged or worn parts such as hydraulic hoses and fittings immediately with manufacturer approved replacement parts. 4. Do not change the engine governor settings or overspeed the engine. This increases the hazard of personal injury. The maximum engine speed is preset by the manufacturer and is within safety limits. 5. Do not alter your splitter in any manner such as attaching a rope or extension to the control lever or adding to the width or height of the wedge. Such alterations may cause your splitter to be unsafe. 6. Perform all recommended maintenance procedures before you use your splitter. 7. Do not service or repair your log splitter without disconnecting the spark plug wire and moving it away from the spark plug. 8. Never store the equipment with gasoline in the tank inside of a building where ignition sources are present, such as hot water and space heaters, clothes dryers and the like. Allow the engine to cool before storing in any enclosure. 9. Always store gasoline in an approved, tightly sealed container. Store the container in a cool, dry place. Do not store in a building where ignition sources are present. 10. To reduce fire hazard, keep engine free of grass, leaves, wood chips, and excessive grease and oil. 11. The hydraulic system of your log splitter requires careful inspection, along with the mechanical parts. Be sure to replace frayed, kinked, or otherwise damaged hydraulic components. 12. Fluid escaping from a very small hole can be almost invisible. Do not check for leaks with your hand. Escaping fluid under pressure can have sufficient force to penetrate skin, causing serious personal injury. Leaks can be located by passing a piece of cardboard or wood over the suspected leak and looking for discoloration. 13. Should it become necessary to loosen or remove any hydraulic fitting or line, be sure to relieve all pressure by shutting off the engine and moving the control handle back and forth several times. 14. Do not remove the cap from the hydraulic tank or reservoir while your log splitter is running. Hot oil under pressure could cause injury. 15. The pressure relief valve on your splitter is preset at the factory. Do not adjust the valve. Only a qualified service technician should perform this adjustment. 16. Completely drain fuel tank prior to storage. This guards against accumulation of fuel fumes which could result in afire hazard. 17. Never store log splitter outside without a waterproof cover. Rain will cause rust on the inside of the cylinder. A ** TOWING 1. This unit should not be towed on any street, highway or public road without checking the existing federal, local or state vehicle requirements. Any licensing or modifications such as tail-lights, etc., needed to comply with the existing federal, local or state vehicle requirements is the sole responsibility of the purchaser. 2. Before towing, be certain the log splitter is correctly and securely attached to the towing vehicle, and the safety chains are in place. Leave slack in chains for turning allowance. 3. Do not allow anyone to sit or ride on your splitter. They can easily fall off and be seriously injured. 4 ASSEMBLY INSTRUCTIONS Tools Required for Assembly (1) Soft Hammer or Mallet (2) 9/16" Wrenches* (2) 1/2" Wrenches* (1) 7/16" Wrench* (1) Adjustable Wrench (1) Screwdriver (1) Pliers (1) Knife (1) Cutters ‘Adjustable Wrenches may be used. Other Materials Required for Assembly: Engine Oil Unleaded Gasoline Approximately 4 Gallons of Dexron II Automatic Transmission Fluid or 10W Non-Foaming Hydraulic Fluid IMPORTANT: This unit has been shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil before operating your log splitter. Refer to the separate engine manual. UNPACKING A WARNING: Exercise extreme caution as parts are very heavy. Mechanical handling equipment should be used, or sufficient people to prevent injury. Remove the log splitter parts from the carton by cutting the corners of the carton. Make certain all parts and literature have been removed from the carton before the carton is discarded. Most of the hardware for assembly of the log splitter has been placed in position on the various parts...