Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
x 7' 2 1/4" D. x 8 1/2' H. • Consult your local authorities for any permits required to construct shed. Prior to the construction of your shed, check with the local building code official to review any required permits or building limitations. • A level and sturdy foundation is required before shed construction can begin. Site preparation information is available on page 9. • Read instructions thoroughly prior to assembly. This kit contains parts that can be damaged if assembled incorrectly or in the wrong sequence. • Please follow instructions. Suncast is not responsible for replacing parts lost or damaged due to incorrect assembly. • Check for all parts before you begin assembly. Using the provided parts check list on pages 3-8, verify that you have all the parts required to construct your shed model. COMPLETE SITE PREPARATION AND FOUNDATION CONSTRUCTION BEFORE UNPACKING ALL PARTS. • Assistance is required during entire assembly. • Proper site preparation required. • Shed not intended for use in extreme weather conditions. • Shed not intended for storage of flammable or caustic chemicals. • Store heavy items near the bottom of shed. • Shed not intended for use by children. • DO NOT stand, sit, or store items on storage shed roof. • Treat carefully in extreme temperatures. • Repair or replace broken parts immediately. • Suncast is not responsible for damage caused by weather or misuse. • At regular intervals inspect your shed to make sure that assembly integrity has been maintained. • Periodically check that the location you have chosen to set your shed is still level. • This kit contains parts with metal edges. Please be careful when handling. A © 2010 Suncast Corporation, Batavia, IL 0361135 web Shed Safety and Care • Wash shed with garden hose or mild detergent solution and soft cloth. DO NOT use a stiff brush or abrasive cleaner as that could damage shed. DO NOT use bleach or other caustic cleaners. • Hot items, such as recently used grills, blowtorches, etc., must not be stored in the shed. • Heavy articles should not be leaned against the walls, as this may cause panel distortion and permanent damage. • Keep roof clean of snow and leaves. Tools Needed for Installation Assembly Day Tips • Complete site preparation and foundation construction before unpacking parts and beginning assembly. • DO NOT attempt to assemble on a day with strong winds. • DO NOT attempt to assemble on days when temperature is below 32 degrees. • Set aside appropriate amount of time to completely assemble shed. Assembly time is approximately 3 hours. • Make sure you have assistance nearby to lift and secure parts in place. • Wear light duty work gloves while assembling shed. • Once roof is assembled, a flashlight may be of use when assembling smaller components inside shed. Note: This product contains parts that are used in different orientations to construct the shed. Please take note of the orientation of the parts shown throughout this instruction manual. Failure to follow instructions could result in damage to parts. Suncast is not responsible for replacing parts lost or damaged due to incorrect assembly. 2 Parts (i I O 0B00043C1 - Side panel 0B00031C1 - Left back panel x4 O 0B00038C1 - Left front panel 0B00029C2 - Floor front 0B00030C1 - Right front panel 0B00023C2 - Floor rear ^0 0B00027C1 - Right back panel 3 Parts 0B00045C1 - Left door 0510586-Door window gasket x2 0B00046C1 - Right door 0510585-Door window x2 Parts @ 0280344 -Ridge beam O 0510555-Vent screen x2 0102085C2 — Header vent x2 0280372-Header beam x2 O 0510541 - Roof ridge beam bracket x2 0B00033C1 - Left rear header 0B00034C1 - Right rear header 0B00036C1 -Front header 5 Parts (®) 0B00042C2 - Left roof x2 0510551 - Truss bracket 0510548-Truss leg x2 0510542-Truss cross beam 0B00037C2-Right roof x2 é 010208810A-Roof connector x6 0510545 - Truss tie down x2 6 Hardware o o © 0102087C1 - Panel connector pin x38 o 0510550-Metal hinge plate x8 0200025 - 2" Hex head cap screw x6 0210171 - .25 - 20 x.75 machine screw x8 x16 0210178-No. 8 x.5 washer head screw x25 cap screw x2 head screw x70 Shown Actual Size 7 Door Handle 0440565 - Door Handle Rod Kit (J) 051058-Rod 0440543 - Door Handle Kit © 0510581 - Left handle plate 0510582 -Handle stop 0 0510576- Doorhandle x2 © 0510579-Inside handle plate x2 Hi. © 0230046-Actuator washer 0510577-Clip x2 0510578 -Header latch plate 0510580 -Right handle plate ©J 0510583 -Handle actuator Hardware 0230050-Washer x4 Shown Actual Size 0220035-Thumb nut x4 0210171 - .25-20 x.75" machine screw x4 8 Site Preparation and Platform Construction (Materials NOT supplied with Shed Kit) Note: Site preparation is required for this shed. Placing the shed on a constructed foundation is highly recommended. Without a constructed foundation, settling will probably occur, causing distortion and damage to the shed. Suncast ...