Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
Completely loosen the pump intake nut. Retain the O-ring if it is loose. Completely loosen the two heater nuts. Retain the O-rings if they are loose. Cut and remove the two pump banding straps. Unplug the control cable from the pump control outlet. Lift the pump motor and heater assembly out of the area. NOTICE: Do not lift the whirlpool by the piping or pump, or use the piping or pump for structural support of the whirlpool. To avoid damage to the whirlpool, lift at the sides of the whirlpool. With help, carefully position the whirlpool in the drop-in cutout. Tilt the whirlpool as needed so the pump end enters the cutout first. Secure the whirlpool to the subfloor as described in .Secure the Whirlpool to the Subfloor.. Reposition the pump motor and heater assembly. Be sure the O-rings are in place, and securely hand tighten the pump intake and heater nuts. Plug the control cable into the pump control outlet. Pump Intake Nut O-Ring Heater Nuts Pump Banding Straps Control Cable Pump Motor Assembly Pump Control Outlet Tilt the whirlpool so the pump end enters the cutout first. Kohler Co. 7 1019749-2-M 5. Secure the Whirlpool to the Subfloor NOTICE: Do not lift the whirlpool by the piping or pump, or use the piping or pump for structural support of the whirlpool. To avoid damage to the whirlpool, lift at the sides of the whirlpool. Choosetheinstallationoptionthatbestappliestoyourparticularinstallation.Followtheappropriateinstructions. If the subfloor is not level, shim the whirlpool support blocks as necessary. Option for Using a Cement or Mortar Bed Spread a 2.(51 mm) thick layer of cement or mortar on the subfloor where the whirlpool will be set. This will help secure, level, and support the unit. Clear all the material away from the pump control and support block locations. NOTE:Do not use gypsum cement or drywall compound for this application, as they will not provide an acceptable, durable bond. NOTE:Thepumpcontrol(whenthepumpbandingstrapsarecut)andsupportblocksmustrestdirectlyonthesubfloor. Position a piece of plastic drop cloth material on top of the cement or mortar bed. With help, carefully lift the whirlpool into place, and make sure the pump control and support blocks do not rest in the bed material. Insert the drain tailpiece into the trap. Make sure the whirlpool is level and resting on all support blocks. Option for Using Construction Adhesive Apply a generous amount of high-quality construction adhesive to the bottom of the support blocks. With help, carefully lift the whirlpool into position. Insert the drain tailpiece into the trap. Make sure the whirlpool is level and resting on all support blocks. Option for Using Silicone Sealant With help, carefully lift the whirlpool into position. Insert the drain tailpiece into the trap. Make sure the whirlpool is level and resting on all support blocks. Apply a continuous bead of high-quality silicone sealant around the entire rim of the whirlpool. Clear space for pump. Clear spaces for support blocks. Spread a 2" (51 mm) layer of cement or mortar bed material. Apply a bead of silicone sealant around the entire rim or Apply construction adhesive to the support blocks. Choosetheinstallationoptionthatbestappliestoyourparticularinstallation.Followtheappropriateinstructions. If the subfloor is not level, shim the whirlpool support blocks as necessary. Option for Using a Cement or Mortar Bed Spread a 2.(51 mm) thick layer of cement or mortar on the subfloor where the whirlpool will be set. This will help secure, level, and support the unit. Clear all the material away from the pump control and support block locations. NOTE:Do not use gypsum cement or drywall compound for this application, as they will not provide an acceptable, du...
Эта инструкция также подходит к моделям:Прочие аксессуары для дома - K-1014 (2.57 mb)
Прочие аксессуары для дома - K-1110 (2.57 mb)
Прочие аксессуары для дома - K-1158 (2.57 mb)
Прочие аксессуары для дома - K-1368 (2.57 mb)