Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
. Assemble the product on the open flat carton or a rug to protect the product and your floor. Some heavy products need a second person to assist in the assembly. Use of power tools is not recommended. It is strongly recommended that at least two people carry out the assembly. Assemble the product close to a wall. Screwing wall anchor into stud is very important to secure the stand. With each step, first insert and hand-tighten all bolts and screws by hand. After ALL BOLTS are slightly screwed in, fully tighten bolts with Phillips screwdriver in sequential pattern (clockwise or counter clockwise). ! Caution: Never let children climb on furniture or play with furniture. Do not sit or stand on furniture. Do not place aTV that is heavier than the recommended load rating on the furniture surface. Do not overload shelves. Use care when moving furniture. Furniture can tip over if moved improperly. Only move furniture when it is empty of TV or other electronic components. Improper handling can result in cuts and lacerations. Do not install on sloping surface. Care Instructions: Use electrostatic dust cloths to clean furniture. Do not set hot or cold containers directly on the furniture surface. -1 Part List Item Components parts list Qty A 1 B 1 C 1 D 3 E 3 F 1 G 1 H 2 Tool needed (not included) Item Components parts list Qty I 12 J 8 K 2 L 4 M 6 N 15 O 5 P 1 Q 1 R 1 S 1 T 1 -2 1 1 A B C 1-Attach frames (B) & (C) to the back panel (A) with screws (J). J*8 D D D C I*12 2 B 2-Fasten beams (D) to the frames (B & C) with screws (I). -3 3 3 O*5 B D D D C N*15 3-Place pads (N) on the beams (D) and frames (B & C). Apply pads (O) at the bottom of the unit. 4 A F L*4 E E E 4-Attach holder (F) to panel (A) with screws (L). Place glass (E) on the pads. -4 E E E 5 M*6 E E E 5 M*6 5-Fasten the glass (E) on the beams with screws (M). Do not over tighten screws. 6 H H 6-Fasten two TV mounting brackets(H) on the back panel of the TV. Detail assembly instructions refer to next pages. -5 PAY EXTRA CARE AND ATTENTION TO THIS STEP. MAKE SURE THE APPROPRIATE MOUNTING HARDWARE IS BEING USED PROPERLY. 1. Select correct Mounting Hardware according to the screw hole size on your TV, discard any remaining Machine Screws or Spacers. 2. Carefully lay your Plasma/Flat Panel TV on its Face on a non-abrasive surface, making sure to lay padding undermeath it so as not to damage the screen. 3. Place left Mounting Rail and Right Mounting Rail in the appropriate position, making sure they are CENTERED on the back of the TV and LEVEL with one another. MOUNTING HARDWARE LIST HARDWARE IDENTIFICATION U1 U2 U3 V1 V2 V3 W3 W2 W1 PICTURE SIZE (mm) T1 T2 T3 4 x 15 4 x 35 4 x 54 5 x 54 6 x 54 8 x 15 8 x 35 8 x 54 5 x 35 5 x 15 6 x 15 6 x 35 HEAD DIAMETER (mm) 8 8 8 8 8 8 10 10 10 14 14 14 - 6 - O8 O6 X O5 O4 7 For Flat Back TV X X X X X X (T1~T3 Screws) (U1~U3 Screws) X X O6 O8 O4 O5 (V1~V3 Screws) (W1~W3 Screws) 7-Insert Machine Screws through Dual-Hole Washers (X) (see Mounting Hardware list), then into appropriate hole locate on left and right mounting brackets(H), and then into TV. NOTE:The position of the Mounting Brackets and Hardware will be determined by the type of TV that you have. These diagrams are not designed to show the exact positioning; they are only to be used as a guide. SECURE MACHINE SCREWS FULLY, BUT DO NOT OVER-TIGHTEN. - 7 7-AH side view F 8 8-After mounting the brackets (H) to TV, hang TV onto holder (F), see (7-A). 9 GAK*2Hs T 9-Attach holder (G) to bracket (H), fix holder (G) and wall strap(S) to panel (A) with washer(T) and screws (K). -8 10 (Q) (R) Tool needed(not included) wall strap wall (S) R Q 10- Place wall strap (S) at desired position on the wall. Mark the hole position with a pencil. Drill a holeon the pencil mark made on the wall with a 10mm size Drill Bit. Insert plastic anchor(Q) into the wall. Fasten the wall strap(S) to the wall by inserting screw(R) through grommet in nylon strap(S) and then into wall anchor. Note:Screwing wall anchor into stud is very important in properly securing the stand. - 9 Max. 100 lbs Max. 65 lbs Max. 65 lbs Max. 65 lbs Product Warranty: Atlantic Inc., warrants to the original purchaser that its products are free from defect in materials or workmanship. If after inspection, we find that the product was defective in materials or workmanship, we shall repair or replace the product at our discretion. This warranty does not cover accidental damage, misuse, improper care or alteration and excludes claims for incidental or consequential loss. This limited warranty applies to product purchased in the U.S. and Canada. This warranty gives you specific legal rights and you may also have other rights which vary from State to State. This warranty will last one year. Keep this Instruction Manual for future reference. Keep your original proof of purchase (store receipt). If parts are missing, DO NOT return to the store. To order missing / replacement parts or for assembly assistance please contact custo...