Оценок - 4, средний балл: 4 ( )

Производитель: Philips Размер: 5.48 mb Название файла: e82b0ad3-ef4c-4c74-51ae-453e20c9cca0.pdf Язык инструкции:

68 Ti.ng Vi.T 82 .... 97 .... 112 HQ9190, HQ9171, HQ9170 4 important EnglisH 4 important EnglisH Read these instructions for use carefully before using the appliance and save them for future reference. -Only use the powerplug supplied. -The powerplug transforms 100-240 volts to a safe low voltage of less than 24 volts. -The powerplug contains a transformer. Do not cut off the powerplug to replace it with another plug, as this will cause a hazardous situation. -Do not use a damaged powerplug. -If the powerplug is damaged, always have it replaced by one of the original type in order to avoid a hazard. -Make sure the powerplug does not get wet. -Charge and store the appliance at a temperature between 5 C and 35 C. cc -Never immerse the charging stand in water nor rinse it under the tap. -Do not recharge the shaver in a closed pouch. -Always unplug the shaver before cleaning it under the tap. -The appliance complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap. Be careful with hot water.Always check if the water is not too hot, to prevent your hands from getting burnt. Electromagnetic fields (EMF) This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and in accordance with the instructions in this instruction manual, the appliance is safe to use according to scientific evidence available today. EnglisH This appliance offers you the unique possibility to , choose the display layout you prefer: a number layout or a battery symbol layout. 1 Press the on/off button approx. 3 seconds to enter the menu. The menu has three different modes: the travel lock mode and two display layout modes. You will enter the menu in the travel lock mode, , indicated by a rotating key symbol. You can scroll through the three modes (travel lock, battery symbol layout and number layout) by pressing the on/off button briefly in quick succession. 2 To select one of the two display layouts, stop pressing the on/off button when the layout you prefer appears on the display. 3 Wait a few seconds without pressing the on/off button until you hear a beep. This beep indicates that the display has been set to the selected layout. Note:The first mode you enter after pressing the on/off button for 3 seconds is the travel lock mode (indicated by a rotating key symbol). If you do not press the on/off button again within a few seconds, the travel lock is activated and the display will not switch to the first display layout mode.To deactivate the travel lock, press the on/off button for 3 seconds again (see chapter ‘Storage’). You can change the display layout at any time. Note:When you start using the appliance for the first time or after a long period of disuse, it could take several minutes before anything appears on the display. The display EnglisH EnglisH The display provides the following information: Charging Number layout: When the shaver is being charged, the display shows the minutes indication and the plug symbol with a blinking power symbol. Battery symbol layout: , When the shaver is being charged, the display shows the battery symbol and the plug symbol with a blinking power symbol. Battery fully charged , , , As soon as the battery has been fully charged, the word FULL runs across the display. After a few hours the word FULL stops appearing.The display shows the minutes indication and the plug symbol. Battery running low , Number layout: When the battery is running low, the display shows a blinking minutes indication and blinking plug symbol when you switch the shaver off. HQ9190 only: you will also hear a few short beeps. , Battery symbol layout: When the battery is running low, the display shows a blinking battery symbol and blinking plug symbol when you switch the shaver off. HQ9190 only: you will also hear a few short beeps. EnglisH Battery empty To indicate that the battery voltage is too low to , operate the appliance, LO appears on the display. Recharge the battery. See chapter ‘Charging’. , Cleaning shaver When the shaver is due to be cleaned, the tap , symbol with blinking water drops appears on the display. Replacing shaving heads When the shaving heads need to be replaced , (every two years), the shaving unit symbol starts blinking when you switch the shaver off. HQ9190 only: at the same time you will hear a beep. -If you do not replace the shaving heads right away, the shaving unit symbol remains visible during the next 7 shaves. -You can reset the appliance by pressing the on/off button for 3 seconds while the shaving unit symbol is blinking.The shaving unit symbol then disappears. HQ9190 only: you will hear a short confirming beep. -If you have not reset the system after these 7 shaves, the system will automatically reset itself. Demonstration program The appliance has a unique demonstration program. Press the on/off button for seconds. , After 3 seconds the lock symbol appears; keep the on/off button pressed. The demo...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: