Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length. MAKE WATER SUPPLY CONNECTIONS .. Channel Locks Adjustable Wrench Plumbers' Putty or Caulking TOOLS REQUIRED .. INSTALL FAUCET 1340.225 1340.255 1340.265 Certified to comply with ANSI A112.18.1 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Installation Instructions METERING Center Set Faucets FERRULE COUPLING NUT 2 3 4 5 1 1 2 NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE PURCHASED SEPARATELY. Insert faucet SHANKS through holes of SINK or MOUNTING SURFACE. Install GASKET (2), FRICTION WASHER (3), DEEP WASHER (4) and LOCK NUT (5). onto SHANKS (6). Tighten LOCK NUTS (5) firmly to secure FAUCET (1). Apply a bead of PUTTY along the edge of the underside of the FAUCET (1). SINK OR MOUNTING SURFACE PUTTY SHANK Turn off hot and cold water supplies before beginning. CAUTION 1340.225 1340.255 1340.265 2.5mm Hex Wrench PRESS HANDLE DOWN TO OPERATE Turn on water supplies and check connections for leaks. Remove AERATOR (1) with KEY (2) supplied. Operate HOT and COLD HANDLES by pressing down on HANDLES. Both Hot and Cold handles are set for approximately 8 second operating cycles. Replace AERATOR (1). Unthread SPOUT NUT (1) and remove SPOUT (2) Remove SPOUT CLIP (3) and O-RINGS (4). Replace RUBBER RING (5) with separate PLASTIC RING (6) supplied with faucet. Replace SPOUT CLIP (3) and O-RINGS (4). Reassemble SPOUT (2) TO BODY. .. TEST INSTALLED FITTING Remove HANDLE (1) by removing INDEX BUTTON (2) and SET SCREW (3) with a 2.5mm hex wrench. Pull off HANDLE (1). To increase cycle time, turn the gray PLASTIC ADJUSTING NUT (4) clockwise. To decrease cycle time, turn the gray PLASTIC ADJUSTING NUT (4) counter-clockwise. Replace SET SCREW (3), INDEX BUTTON (2) and HANDLE (1). Test faucet for proper operation and cycle time. TO ADJUST CYCLE TIME CONVERT RIGID SPOUT TO SWIVEL SPOUT (1340.255; 1340.265) SERVICE 1 2 WATER SUPPLIES 1 2 3 1 3 4 5 6 2 4 TO INCREASE CYCLE TIME ROTATE CLOCKWISE REMOVE RUBBER RING INSTALL PLASTIC RING TO DECREASE CYCLE TIME ROTATE COUNTER-CLOCKWISE 2.5mm HEX WRENCH .. CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. Remove HANDLE (1). Refer to Step 4 for handle removal. Remove ACTUATOR ASSEMBLY (2). Remove WASHER (3). Pull out VALVE ASSEMBLY (4) and FILTER SCREEN (5). Inspect that VALVE ASSEMBLY (4), FILTER SCREEN (5) and VALVE SEAT (6) are clean and free from debris. VALVE ASSEMBLY (3) and FILTER SCREEN (5) can be cleaned with soap and water. Replace FILTER SCREEN (5) and VALVE ASSEMBLY (4). Place WASHER (3) on top of VALVE ASSEMBLY (4). Th...
Эта инструкция также подходит к моделям:Прочие аксессуары для дома - 1340.255 (659.93 kb)