Оценок - , средний балл: ( )

Инструкция по эксплуатации Arrow Storage Products, модель OB1014-B

Производитель: Arrow Storage Products
Размер: 2.08 mb
Название файла: 63bb16a4-3c8e-467e-9afd-426064e9d010.pdf

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Hint. The bolts on the ridge cap need to be leR Ioose to move the ridge cap to the side and overlap the ribs of the next roof panel. Continue weather stripping the ridge. NOTE If roof beam holes do not line up with the roof panel holes, shift the building from left to right. If this does not help, your building may not be level. Shim the corners until holes line up. 6869 Weather Stripping Tape 7743 Roof Panel 7743 Roof Panel Q6797Ridge Cap (1) • Parts Needed For • o 7743 Roof Panel (2) Step 17 Riagec.pa P..d. .9083Lo,,Roo, ooe,,,, Q 9984 Right Roof Panel (1) $P30 J Insta!l the third ridge cap 6797 overlapping the second ridge cap while installing the remaining two roof panels 7743. Hint. The bolts on the ridge cap need to be left loose to move the ridge cap to the side and overlap the ribs of the next roof paneL Continue weather stripping the ridge. 2 Install the left 9983 and right roof panel 9984 as you unroll the weather stripping tape, and press it down. Fasten the lower end of the panels to the side wall angles using screws and washers. 3 Fasten the roof panel ribs, peak cap and ridge cap together using bolts and nuts. 6797 7743? 9984 Peak Cap Cut Weather Stripping and Fold Under 3O • Parts Needed For • O6893LeftSJdeRoofTrim(2) Step 1 RoofT i .°01°SideRoofT.m, O 6892 Right Side Roof Trim (2) SP31 1 Attach the right, left and side roof trim pieces to the Jower end of the roof paneJs on each side of the buiJding using screws at each panel overlap. NOTE A single screw fastens both pieces at the overlap. i trim | 2 Using your thumb and index finger, overbend the bottom flange of the roof panel rib at the corner inward enough so the right and left roof trim caps fit onto right and left corners. 3 Fasten the side trim using roof trim a screw. caps to the 6893 Roof Trim Cap . 6892 6015 6892 RoofTrim 6893 6015 Tuck Flange tnward to Fit Inside of RoofTrim Cap • 3719 Door Handle Brace (2) Right Door (1) O 8539 Left Door (1) Step 19 "Dool'PartsNeededAhlvF°r®8838• =_SSe][H,.,=j • 6264 Horizontal Door Brace (4) so3_ O 6278 Vertical Door Brace (2) The steps on this page tell how to assemble the right door. You will perform exactlythe same procedures for the left door. Each bolt and screw in the door requires ceed as follows: a washer. Pro1 Attach the door handle handle to the door with brace and 1 bolt as 6264 3719 shown. Don't tighten the bolt yet. 2 Swing the door handle brace up to the hole on the center of the door and insert a screw. 66382 ._ .'/ // Right Door 3719 :3 Hold the vertical door brace 66382#_ against the center of the inside surface of the door and turn the screw to hold the vertical door brace and door _6264 handle brace door above in place. Fasten to and below center connection using 2 screws. 4 Insert a second bolt in the door 6278 handle and tighten 5 Put a horizontal both door bolts. brace onto / the top edge and bottom edge fasten with 1 bolt in the center. and 6 Attach shown. the lower door guides as 6264 7 Repeat left door. steps 1 through 6 for the ENDVIEW SHOWING: DO, 66382 _ • Parts Needed For • o RightDoorAssembly(l} Step 20 Door Installation & Adjustment • LeftDoorAssembly(1) SQ33 I From inside the building, put the bottom of the right door assembly (on your left when you are inside the building) behind door jamb into the front fra me track. 2 Position the top of the door so that the holes in the door line up with the holes in the door slides, :3 Fasten the door to the door slides using a #10Bxl/2" screw. NOTE The four holes in the top of each door allow you to adjust the doors. Place the door slide in the middle 2 holes. 4 Repeat steps 1 through 3 for the left door. Gable _ Horizontal Door Brace UoorTrack _ _ I t Door Slide t!/;/ o C3 II fI t_ i! ;/ if :i P_ FrontFloor FrameAssembly #10Bxl/2" Screw J Adjustment Holes Allow Doors to Meet Evenly Along Their Length m STEP 4 SOME FACTS ABOUT RUST SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use. Identifying these natural rusting problem areas and taking some simple rust protection precautions can help to stop rust from developing, or stop it quickly as soon as it appears. 1. Avoid nicking or scraping the coating surface, inside and out. 2. Use all the washers supplied. In addition to protecting against weather infiltration, the washers protect the metal from being scraped by the screws. 3. Keep roof, base perimeter and door tracks free of debris and leaves which may accumulate and retain moisture. These can do double damage since they give off acid as they decay. 4. Touch up scrapes or nicks and any area of visible rust as soon as possible. Make sure the surface is free of moisture, oils, dirt or grime and then apply an even film of high quality touch-up paint. ...