Оценок - 3, средний балл: 3.7 ( )

Производитель: Arrow Storage Products Размер: 2.08 mb Название файла: Язык инструкции:

The crimped rib should go under the rib of the panel that follows it. Crimped Rib Underneath 1 Locate all of the wall panels and set each one alongside the building. 2 Fasten the wall panels at the top and bottom with screws. 6515 Detail Showing Center of Panel Screwed to Wall Channel 3 Fasten the center of each panel the wall channel with screws. to 4 Fasten overlapping ribs as before. Panels rest o frame as shown 3olt and nut does not go thru wall channeIat overlap Use bolts and nuts thru wait angle overlap at the top of panel at rear. ® Parts Needed For O O 9369 Door Jamb (2) Step 1 Front Channel/Door Jamb O 9365 Front Wall Channel (2) SO23 The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both doorjambs. 1 Fasten the front wall channels in their positions between the end of the side wall channel and the corner panel using screws. Do not put a screw in the hole at the end be hind the door opening at this time. '_ Fasten a door jamb to the front panel with two bolts, nuts and acorn nuts, as shown. 3 Fasten the center of the door jamb to the frontwall panel and the front wall channel with two screws. 9365@ l INSIDE OF BUILDING (2; Acorn Nut \ Hex Nut Front WallChannel Cross-Section Top View Acorn Nut 9369 Screw Screw 4 Fasten the top of the doorjamb to Screw the door track with two screws. Do the same for the bottom into frame. Repeat steps 2 through 4 for the opposite door jamb. • Parts Needed For • eSS'tSR,ghteab,e(2) Step 11 Gable Assemblies o as_7Le_Gable(2) O 6635 Roof Beam Bracket (4) SR_4 The gables go on top of the front and rear wails to support the roof beams. NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. '1 Attach the four roof beam brackets to the gables using two bolts, washers and nuts. NOTE Mounting leg of bracket must face toward center of gable. 8577 6635 Roof Beam Brackets 8576 Washer _, 6635 Roof Beam Brackets • Parts Needed For ® • Left Gable Assemblies (2) @ Right Gable Assemblies (2) Step 12 Gables/Braces • 9009 Gable Brace (2) $.25 I Lift and fasten a right and left gable, under angle at corner, to the door track and rear wall angle with screws. Hint: On the front gable, leave out2 screws closest to center gable leg. On the reargable, usea boltand nut at the overlapping rear wall angle. 2 Join the left and right gables together with a gable brace using a bolt and nut in the second hole from the bottom only. Repeat Steps 1 & 2 for the opposite side of building. 3 Fasten the track supports to the front gable assembly only as shown. Gable Brace Track Supports 6228 ® Parts Needed For ® O Main Roof Beam Assembly (1) O Single Roof Beam Assemblies (2) Step 13 Roof Beam//Braces O 9204 Roof Beam Brace (2) SP26 I Wrap the weather stripping tape around the two joined edges of the large left and right gables. See diagram. Cut the weather stripping to length and repeat on next gable set. 2 Spread the two halves ofthe double roof beam and fasten to the gable brace of the front gable. 3 Fasten the other end of the double roof beam to the gable brace of the rear gable. 4 Fasten the single roof beams, small holes on top, as shown using bolts and nuts. 5 Fasten a roof beam brace to the double roof beam behind the front gable by placing the tab on the end of the brace between the roof beams. Align the tab with the fourth hole and fasten the brace with a bolt and nut. 6 Fasten the lower end of the roof beam brace to the track support with a bolt and nut. 7 Fasten a roof beam brace be tween the rear gable and the roof beam at the third hole, as shown. Weather Stripping Spread Two Halves jOf Roof Beams / Roof Beam (Double) Roof Beam (Single) Roof Beam Brace 9204 Roof Beam Brace 9204 Step 14 . Parts Needed For ® .9984R,ghtRoo.Pane,(,) Right Roof Panel Sp-_7 Installing the roof panels is best done with a step ladder. Install the first roof panel at the back right corner of the building. Each screw and bolt in the roof requires a washer. NOTE Measure the building diagonally again and make adjustments to make sure the building is square and level. This will make the roof (6) Screws panels fit better, and holes will align. Don't anchor the floor frame. NOTE if a Roof Beef-Up Kit was purchased, assemble prior to attaching the roof panels. I Locate the roof panels and find the right roof panel part number 9984. 2 Position the right roof panel at the 9984 Right Roof Panel Bolt back right corner and fasten to the gable with six bolts and nuts and roof beams using six screws. Do not fas! ten the lower end of the panel to the side wall angle at this time. (3) Screws O Parts Needed For O Q 9983 Left Roof Panel (1) O 7743 Roof Panel (2) Step 15 Ridge Cap & Panels O 6797 Ridge Cap (1) SP28 I Install a left roof panel 9983 atthe left rear corner of the roof. '_ Cover the joint at the peak with weather stripping tape. Unroll the tape and press it down over the opening at the ridge as you install each...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: