Оценок - 4, средний балл: 3.5 ( )

Производитель: Broan Размер: 2.14 mb Название файла: Язык инструкции:

electrical outlet 12” min. cord clamp The compactor is equipped with a 6-ft. long power cord. Use the cord clamp to prevent excess power cord from being pinched beneath the cabinet during installation or service. cord clamp Installation reversing the door (optional) Door Reversal Instructions for all doors (except wood and tile). As shipped, the compactor door is hinged on the right (when looking at the unit). To change door to be hinged on the left: 1. With the door closed, use a 3/16” allen wrench to remove the lower hinge pin. 2. Carefully remove door by opening and sliding the bottom of the door away from the cabinet. 3. Use a 3/16” allen wrench to remove the lower hinge bracket from the cabinet (2 screws). 4. Turn the bracket over and install the bracket on the opposite side of the cabinet using the same screws. 5. Use a screwdriver to remove the upper hinge pin from the trim piece and reinstall the pin on the opposite side. leveling the compactor Your compactor has four adjustable levelers; (2) rollers in the rear and (2) legs in the front. They allow you to adjust for uneven floors and also trim the unit up to fit an under- counter installation. To level the back of the compactor: Tip the back of compactor up and onto a wood block. Loosen the adjusting screws only far enough to move the rollers to a higher or lower slot. Retighten the adjusting screws and remove the wood block. To level the front of the compactor: Tip the front of compactor up and onto a wood block. Turn the leveling legs in or out to the desired position. Remove the wood block. back of compactor slots door adjusting screws lower hinge bracket wood block screws lower hinge pin rollers front of compactor wood block leveling legs trim piece upper hinge pin Installation 3. Consider where the compactor will be installed and determine whether to hinge the door on the left or right side of the cabinet. Since the hinge pins are permanently attached to the door pan, simply rotate the door pan until the hinge pins are on the desired side. You may want to mark the inside of the door pan to indicate the top. 4. To prevent damage to the actuator on the back of door, remove the (2) screws that hold it in place. Save the actuator and screws. For wood door: 5. The wood door pan is designed to accommodate a .” thick wood panel that is 14-7/8” wide by 29-1\4” tall. It is recommended that you verify the height of the door pan prior to cutting the wood panel to size. Center the door pan on the wood panel and fasten together using hardware provided in the compactor parts bag. For tile door: 5. The tile door pan comes preassembled with cement backer board. Tile and grout the door pan using traditional tiling methods and materials. 6. Purchase a door handle to match your cabinet hardware and install per handle instructions. 7. If the door will be hinged on the left side of the compactor, it will be necessary to reverse the lower hinge bracket removed in Step 1. Remove the plastic bushing from the hinge bracket and install on the opposite side of the bracket. Install the door onto the compactor cabinet by reversing the procedure from Step 1. 8. Re-install the actuator removed in Step 4. Make sure the door opens and closes smoothly with the actuator entering and exiting the door interlock switch on the compactor. cap bushing door 6. Being careful not to scratch the door, remove the plastic door bushing and cap from the top and bottom of the door using a small flat screwdriver. Install the bushings on the side of the door panel that will be hinged and install the cap on the opposite side. 7. Install the door on the cabinet by inserting the upper hinge pin into the upper door bushing while moving the door into place. Insert the lower hinge pin from Step 1 and tighten securely. back of door actuator Tile and Wood Door Assembly Use the following instructions if you have a trash compactor with a tile or wood door kit. It is recommended you remove the door pan from the compactor to install the custom tile or wood panel. To remove door pan: 1. Use a 3/16” allen wrench to remove the lower hinge bracket from the cabinet (2 screws). 2. Remove the door pan from the cabinet. door lower hinge bracket bushing screws door pan lower hinge bracket screws Start Button (with Ram Status LED) Door Interlock Interlock Actuator Key Lock Compact Mode Switch Bag Storage Area Preparation Odor Disk Ram Compaction Plate Release Tab Compaction Plate Trash Bucket Latches (2) Sliding Trash Bucket Leveling Rollers Leveling Legs 1. how the compactor works The Broan compactor compresses household trash up to 1/6 of its original volume. It will compact normal household trash including milk cartons, glass and plastic bottles, containers and jars, tin cans, wrappings, boxes, food wastes, etc. When you start the compactor, an electrically powered ram moves down into the trash bucket, compresses the trash and then returns to the “UP” position and shuts off automatically. NOTE: The ram travels ab...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: