Оценок - 4, средний балл: 4 ( )

Производитель: GE Monogram Размер: 3.35 mb Название файла: Язык инструкции:

¦ This compactor is intended for household use only. ¦ Use only for intended use as described in this manual. Do not use other than manufacturer's recommended attachments. SAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS Installer: Leave Use and Care Guide with the homeowner. Homeowner: Keep Use and Care Guide for future reference and for local electrical inspector.s use, if required. Unpacking WARNING Excessive Weight Hazard Use two or more people to move and install compactor. Failure to do so can result in back or other injury. IMPORTANT: ¦ Do not grasp console to move compactor. ¦ Begin in the room where the compactor will be located. 1. Remove compactor from shipping carton. Remove all packaging materials such as tape and shipping pads. Use a mild detergent and warm water to remove waxy residue caused by shipping material. Dry thoroughly with a soft cloth. For more information, see .Cleaning.. 2. Be sure the power cord is attached to the cord clip on the rear of the compactor. A A. Cord clip 3. Place the 2 corner posts from the carton on the floor near the compactor. Open the compactor drawer and remove any shipping materials or other items from the drawer. Do not remove the compactor bag. Grasp the handle and raise the front of drawer until it clears the drawer stops. Grasp sides of drawer and lift drawer out of compactor. Place the drawer on the 2 corner posts. 4. Place the other 2 corner posts on the floor to the side of the compactor. Grasp the sides of the compactor cabinet and put compactor on its side on top of the corner posts. Remove the shipping base from the bottom of the compactor. B A A. Leveling legs B. Shipping base Clearance Dimensions Location Requirements Product Dimensions 24" (61 cm)15" (38.1 cm) B A A. Leave 6" (15.2 cm) of clearance space to the right side of the compactor in order to remove the compactor bags. B. Leave 23" (58.4 cm) of clearance in front of the compactor in order to fully open or remove the compactor drawer. 34..." (86.7 cm) Cutout Dimensions A 24" min. (61 cm) 34..." min. (87 cm) 18" min. (45.7 cm) 3" min. (7.6 cm) 15..." min. (38.7 cm) A. Grounded electrical outlet must be a minimum of 3" (7.6 cm) away from surrounding cabinets or nearby walls as shown. It can be placed either to the left or the right side of the compactor. Electrical Requirements WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Recommended Grounding Method This compactor is for use on a single phase, 115-volt, 60 Hz, AC only, 15- or 20-amp fused and properly grounded circuit and is equipped with a grounding plug as shown below. It is recommended that a separate circuit serving only this appliance be provided. This compactor must be grounded while in use to reduce the risk of electric shock. The compactor is equipped with a three-conductor cord and 3 prong grounding-type plug to fit the proper grounding- type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Do not connect the green (or green and yellow) wire to a live terminal. Undercounter Installation NOTE: Proper installation is your responsibility. Make sure you have everything necessary for correct installation. It is the personal responsibility and obligation of the customer to contact a qualified installer to assure that electrical installation meets all national and local codes and ordinances. Tools needed: Gather the required tools and parts before starting installation. ¦ Level ¦ Phillips No. 2 screwdriver ¦ Tape measure ¦ Flat-blade screwdriver ¦ Pliers ¦ ...." Box-end wrench ¦ Scissors ¦ Utility knife IMPORTANT: ¦ Do not grasp control panel to move compactor. ¦ Slide compactor onto cardboard or hardboard before moving compactor across floor to avoid floor covering damage. ¦ Do not allow the rear frame of the compactor to touch the floor covering when lifting or moving compactor. Undercounter Installation NOTE: Installation hardware is not provided with full cabinet models. 1. Measure the height of your cabinet opening. The top of the compactor should be at least .." (3 mm) from the top of the cabinet opening. The rear wheels are preset for a cabinet opening height of 34..." (87 cm) (Position 1). To adjust for other cabinet opening heights: ¦ Loosen self-tapping screw just enough to clear stud fromhole in position .1.. ¦ Move the rear wheel and stud to position .2. or .3. as needed for your cabinet opening measurement: Position 2: 34..." to 34...." (87 to 87.5 cm) Position 3: 34...." to 34..." (87.5 to 88 cm) NOTE: To level the unit in position .3,. you may need to add shims under the leveling legs. ¦ Tighten screw. Repeat for other rear wheel. 2. Use pliers to lower leveling legs away from cabinet. Adjust legs so there will be a ..." (3 mm) to .." (6.4 mm) space between the top of the compactor and the top of ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: