Войти:
Оценок - 4, средний балл: 3.8 ( )

Инструкция по эксплуатации Cornelius, модель 15303

Производитель: Cornelius
Размер: 379.12 kb
Название файла: 001725.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Applicable Models_ Ice Maker Size Wilshire WCC500/700 14 1/2” Wide Table 2. Loose Shipped Parts Item No. Part No. Name Qty. 1 620030602 Lid Assembly, 1 2 15303 Bracket 1 3 50904 RTV, Clear, 732, 3 oz. Tube 1 4 70217 #8 Sheet Metal Screw 5 91957 Label, Disconnect Before Cleaning 1 6 70188 Thumb Screw #8-32 X 1/2” 1 7 620911301 Installation Instruction 1 8 22127 Bracket, Mounting 1 9 620030601 Cover, RH Assembly 1 A, WARNING: Disconnect power to the unit before installing the adaptor following all lockout/tag out procedures established by the user. Verify that all the power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. ^ WARNING: All ice baffle plates and bin stats, if included or recommended in this kit, must be installed as directed in this manual or the equipment manufacturer’s instructions. Failure to comply could result in serious injury, death or damage to the equipment. ^ WARNING: All of the attachment screws and plates must be installed as directed in this manual. Failure to comply could result in serious injury, death or damage to the equipment. 1. Set Ice maker lid on the top of the dispenser and position it flush with the back and sides of the dispenser. 2. Using the slotted holes in the lid as a template, drill four (4) 0.140” diameter holes at the bottom of the slots (see Detail A). Use extreme care not to drill into the hopper. Fasten the lid to the dispenser with four (4) #8 sheet metal screws, two on each side. 3. Seal the ice maker to the top of the dispenser as follows: (Flush with rear and left side) A. Apply beads of RTV around the opening in the lid and inside the perimeter of the ice maker outline so that the ice maker sets on the RTV. B. Set the ice maker onto the lid and position it as required. C. Wipe away any excess RTV. 4. Remove the left rear screw (only) installed in Step 2. Use that screw to install the mounting bracket (item 2) and install the cover (item 9) to the rear of the dispenser and the ice maker. Drill 9/64” diameter holes into the ice maker cabinet using the bracket as a template. Use extreme caution not to drill into any ice maker components (condenser, tubing, etc.). Secure the brackets using the screws provided. Release Date: November 10, 2010 Revision: B © 1998-2010, IMI Cornelius Inc. - 1 - Publication Number: 620911301 “K” Style Lid Kit Installation Instructions 5. Follow the ice maker manufacturers instruction to complete the installation of the ice maker including the bin thermostat, if so equipped or required. CAUTION: Bin thermostat must not interfere with agitator rotation. 6. Place the lid (item 4) in position over the stainless steel flange and install the thumb screw (item 7). W\ CAUTION: The back of the ice maker must be flush with the back of the lid (item 1 ). Publication Number: 620911301 Figure 1. - 2 - © 1998-2010, IMI Cornelius Inc....

Эта инструкция также подходит к моделям:
Прочая кухонная техника - 620030602 (379.12 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории