Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Green Tea should be steeped between 170.F and 185.F, most Oolong teas should be steeped between 190.F and 200.F degrees, water for French Press coffee should not be hotter than 200.F. • Fill your kettle with the desired amount of cold fresh water. Place on power base. The display shows the default setting (Fig. 3a). • Use the arrow buttons (Fig. 2b) to select any temperature between 110.F and 200.F in 10.F increments (110.F, 120.F and so forth) or 212.F. • Push the On/Off button (Fig. 2d). The kettle will heat the water to the desired temperature and then shut off. The display will show the selected temperature and the kettle symbol will stop blinking. When you remove the kettle from the base and replace it, the default setting 212.F will be displayed. 5. WARMKEEPING The warm-keeping feature can be used in two ways: a) to keep water at a certain temperature after it has reached the desired temperature. b) to first boil the water and then bring it down to the desired temperature. • The display shows the default setting (Fig 3a). • Push the program button once (Fig 2c). The display will show the warm keeping symbol and 000.F. • Push the arrow buttons (Fig. 2b) to select the warm-keeping temperature between 110.F and 190.F. Please note: the warm-keeping temperature cannot be set higher than the selected heating temperature, i.e. if the selected heating temperature is set to 160.F, the warm-keeping temperature can be set between 110.F and 160.F. 8. Please note: if the selected heating temperature is set to 212.F or 200.F degrees the warm-keeping temperature cannot be set higher than 190.F. After the selected heating temperature is reached, the display will now change to the preselected warm-keeping temperature. The warm-keeping symbol and the warm-keeping temperature are displayed. Once the water cools to approx. 10.F below the pre-set warm-keeping temperature, the heater will automatically start re-warming the water to the pre-set temperature. During this time the warm-keeping symbol will be blinking. The kettle will keep the selected temperature for up to 40 minutes. After 40 minutes the warm-keeping symbol stops blinking indicating that the heating element has shut off. Please note: once you remove the kettle from the power base, all pre-sets are cancelled. Tip: If you want to pour water immediately after brewing and then keep the rest at a certain temperature, proceed as follows: • Follow the instructions under chapter 1 or 4. • Pour the desired amount of water. • Replace the kettle. • Select the brewing temperature by pushing the arrow buttons. • Push the program button once to show the warm-keeping display 000.F. Use the arrow buttons to select the desired warm-keeping temperature. • Push the On/Off button. The kettle is now on. Depending on the temperature of the water it will either re-heat the water immediately or later. 6. CHLORINE REDUCING SETTING / EXTENDED BOIL SETTING If you boil the water in the default setting, the kettle will shut off 3 seconds after the sensor registered the boiling temperature. You can prolong the actual boiling action as follows: • Set the Chlorine symbol to “CL”, this will add three extra seconds to the boiling of the water. • Change the Timer Setting from 003 (seconds) to any duration up to 20 seconds (020). • Prepare the kettle as explained in chapter 1. • Before you push the On/Off button, push the program button twice, the Chlorine symbol appears (Fig. 3c). • Push either arrow button once, the display shows “CL”. • Push the program button again. The display shows the timer symbol and 003 (Fig. 3d). 9. • Push the arrow button to select up to 20 seconds. • Now push the On/Off button. Once the boiling temperature is reached the kettle will keep boiling the extra three seconds from the CL setting plus the seconds set with the timer. Please note: once you remove the kettle from the base all settings will return to the default (see Fig. 3). 7. CLEANING • Always unplug cord of power base before cleaning. • Make sure kettle is cold. • Clean the exterior surface with a clean, damp, soft cloth. • Never use abrasive cleaners or scouring agents. • Rinse out kettle. Attention: • Over time the stainless steel inside of the kettle may change color slightly. This is caused by the intense heat of the heating element, especially if the kettle was turned on repeatedly without water. This will not diminish the performance of the kettle in any way. • If your water has a high calcium content, calcium deposits might dull the inside. Follow the instruction below for decalcification. 8. DECALCIFICATION Hard water can leave calcium spots inside the kettle. Use a commercial descaling agent and follow the instructions that come with the agent. NOTE: Use of Vinegar You can also use white vinegar to descale the inside. • Fill the kettle up to the desired level with water. • For each 2 cups of water (16 oz) add 6 tablespoons of white vinegar. • Bring to a boil. • Discard the solution and repeat if ne...
Эта инструкция также подходит к моделям:Прочая кухонная техника - H2O PRO 275 (816.79 kb)