Оценок - 4, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
However, if the CUE MODE is LAST CUE, the state of the [CUE] key is not reproduced. LS9-16/32 Owner’s Manual Using the Cue function Using the Cue function n This section explains how you can use the [CUE] key of a desired channel to monitor the Cue signal. NOTE • The cue signal is sent to the same output destination as the monitor signal. Be aware that for this reason, the cue signal will not be sent to the connected monitor speakers if you turn off the Monitor output. However, the front panel PHONES OUT jack will always output the cue signal regardless of the Monitor on/off setting. For details on Monitor function settings, refer to “Using the Monitor function” (> p. 146). 1 In the DISPLAY ACCESS section, press the [MONITOR] button repeatedly to access the CUE screen. In the CUE screen you can check the Cue status, and turn Cue on/off. 1 234 1 CUE MODE field This specifies the mode of operation when multiple [CUE] keys within the same group are turned on. B INPUT field Here you can select one of the following positions from which input channels will be cued. . PFL (Pre-Fader Listen) button The pre-fader signal will be output . AFL (After-Fader Listen) button The signal immediately after the [ON] key will be output . POST PAN button The post-pan signal will be output . PFL TRIM knob If PFL is selected, you can adjust the output level of the cue signal in a range of -20 dB to +10 dB. NOTE • Be aware that if you turn the POST PAN button on, you can no longer use input CUE to monitor the signal sent to the MONO bus from an input channel that is set to LCR mode. C OUTPUT field Here you can select one of the following choices as the position from which output channels will be cued. . PFL (Pre-Fader Listen) button The pre-fader signal will be output . AFL (After-Fader Listen) button The signal immediately after the [ON] key will be output . PFL TRIM knob If PFL is selected, you can adjust the output level of the cue signal in a range of -20 dB to +10 dB. D Meter field . CUE meter This indicates the level of the cue signal. . ACTIVE CUE indicator This indicates the currently-active CUE group. . CLEAR CUE button Clears all Cue selections. 2 Use the buttons of the CUE MODE section to specify what will happen when multiple [CUE] keys within the same CUE group are turned on. Use the following two buttons to choose the Cue mode. . MIX CUE button All channels within the same CUE group whose [CUE] key is on will be mixed for monitoring (MIX CUE mode). . LAST CUE button Only the channel whose [CUE] key was last turned 14 on will be monitored (LAST CUE mode). HINT Monitor/ • [CUE] keys belonging to different CUE groups cannot be turned on simultaneously. The CUE group to which the last- pressed [CUE] key belongs will be turned on, allowing only the signals of that group to be monitored. 3 Use the buttons and knobs of the INPUT field and OUTPUT field to specify the output position and output level for each CUE group. 149 LS9-16/32 Owner’s Manual Using the Cue function Using the Cue function Press the [CUE] key of a desired channel to turn it on. The Cue signal of the corresponding channel will be sent to the monitor signal output destination. You can also watch the Cue meter of the meter field to check the output level of the cue signal. The ACTIVE CUE indicator located below the Cue meter indicates the CUE group (INPUT or OUTPUT) that is currently turned on. HINT CUE meter ACTIVE CUE indicator • If you want Cue operations and channel select operations to be linked, open the PREFERENCE popup window of the USER SETUP screen, and turn “[CUE]>[SEL] LINK” on (> p. 194). 5 Press the DISPLAY ACCESS section [MONITOR] button to access the MONITOR screen, and use the MONITOR LEVEL knob in the screen to adjust the level of the cue signal. If PHONES LEVEL LINK is ON, you can use both the MONITOR LEVEL knob and the front panel PHONES LEVEL control to adjust the monitor level when monitoring through headphones. 6 To defeat Cue, press the [CUE CLEAR] key or the currently-on [CUE] key once again. If you want to clear all Cue selections, move the cursor to the CUE CLEAR button in the CUE screen, and press the [ENTER] key. HINT • All Cue selections will be cleared if you switch between MIX CUE mode and LAST CUE mode in the CUE MODE section. •You can also assign the same function as the CLEAR CUE button to a user-defined key (> p. 196). LS9-16/32 Owner’s Manual 150 5 Talkback / Oscillator This chapter explains how to use the talkback and oscillator functions. About talkback and oscillator Talkback is a function that sends the signal of the selected INPUT jack to the desired bus. This is used mainly to convey directions from the operator to the performers and staff. The LS9 also contains an oscillator that allows a sine wave or pink noise to the desired bus, and this can be used to check external equipment or to test the response of the room. The diagram below shows the signal flow of the talkback and oscillator. TALKBACK ON INPUT 1-16{32} 12...
Эта инструкция также подходит к моделям:Музыкальные инструменты - LS9-16 (6.62 mb)