|
Фрагмент инструкции
3. Using a 7/32" hex wrench, remove the pull roll height adjust crank from the drive side of the machine. 4. Using a 1/8" hex wrench, remove the screws securing the cabinet panel to the drive side of the machine. 5. Inspect all the bolts and tighten any that were loosened during shipping. 6. Set the nip. (See Maintenance for the procedure.) 7. Replace both cabinet covers. 8. Replace the pull roll height adjust crank. screws holding the rear table under the pull rolls. Collect the screws and spacers for reuse. Pivot the table up into position behind the pull rolls and secure in place by installing the bolts into the top set of cabinet holes. Be sure the spacers are in position! Lower Hole in Cabinet Figure 2-6: Installing the Rear Table © GBC Pro-Tech 1999 April F-60+ Operation and Maintenance Manual Installation /HYHOLQ. Tools required: • Adjustable wrench • Carpenter's level To level the laminator: 1. Raise each end, remove the castors and install a leveling pad and stud onto each of the foot brackets at the four bottom corners of the laminator. Thread third nut on stud below cabinet. 2. Thread stud into 4 leveling pads and lock down with nut. Thread second nut onto stud. 3. Place a carpenter's level front to rear across the two lower tie bars at one end of the machine. 4. Level this end of the machine front to rear, raising or lowering the leveling pads by adjusting the middle nuts on the foot bolts. 5. Move the level to the other end of the machine and level front to rear. 6. Place the level directly on one of the tie bars and level the machine side to side. 7. Recheck the front to rear level condition to insure that it has not changed. If it has, repeat the leveling procedure. 8. When all the measurements indicate that the machine is level, tighten down the top nuts on the foot brackets to lock the pads in their current position. 6WDUWX. The first time the laminator is started and every time it is serviced you should use the following checklist to confirm that the unit is operating properly and that all safety mechanisms are functioning. Startup Checklist Start the laminator and go through the following checklist. . Are the emergency stop buttons working? Push down on one of the emergency stop buttons. The laminator should stop. Rotate and pull up on the button and push the reset button on the lower back of the laminator. The laminator should resume operation. Always check all buttons. WARNING Never operate the laminator unless all of the emergency stop buttons are functioning properly. You can be crushed or burned. . Are the guard table switches working? With the laminator running, pull the front guard towards you. The rolls should stop. Move the guard back in. Press the RUN button on the front control panel. The laminator should resume operation. WARNING Never operate the laminator unless the mechanical guard system is operating properly. You can be crushed or burned. . Is the footswitch working? Press the footswitch. The laminator should start operation. Vary the speed using the footswitch (like an automobile accelerator) to ensure that the foot- switch is operating properly at various speeds. © GBC Pro-Tech 1999 April Installation F-60+ Operation and Maintenance Manual WARNING Use extreme caution when operating the machine with the guard off. You can be crushed or burned. . Is the motor functioning? Test the motor at various speeds ranging from 0-15. At 0 the rolls should stop turning. Run the motor in both forward and reverse. . Are the heaters working? Verify that the heater controller heats the top roll. . NOTE The bottom roll heater controller must be turned on before the top roll heater controller will energize the top heater. Once you have completed the startup checklist you can safely run a test sample. © GBC Pro-Tech 1999 April F-60+ Operation and Maintenance Manual Operation Operation 6HFWLR. . . 2SHUDWLR. 6DIHW. The F-60+ Laminator has been designed with safety as a primary consideration. However, you must become thoroughly familiar with the controls, proper operation, proper service procedures, and safety features of the laminator before using or servicing the unit. GBC Pro-Tech F-60+ Laminator is a powerful machine that is designed to mount, laminate and encapsulate. The forces required to accomplish these tasks can vary from negligible to very large. In addition, the laminating roll of the F-60+ can reach temperatures of 270 ° F (132 ° C). At these temperatures there is a danger of a severe burn if the roll is touched during set-up, operation or servicing. Safety is an important feature of the F-60+ Laminator. It has emergency stop buttons and a photoelectric eye system on the infeed. The laminator is equipped with four emergency stop buttons located on the top front and back of either side of the laminator. Any of these, if engaged, stops the laminator. To continue operation all emergency stop buttons must be in the up position and you must press the reset button above the fuse panel o...
Эта инструкция также подходит к моделям:Принтеры - 930-028 (679.58 kb)
Принтеры - 930-028 (679.58 kb)
Принтеры - 930-028 (679.58 kb)
Принтеры - 930-028 (679.58 kb)