Оценок - 3, средний балл: 4.7 ( )

Производитель: Panasonic Размер: 679.58 kb Название файла: F60P_CE_OP_MAN.pdf Язык инструкции:

Allow the laminator to cool slightly to no higher than 110.F (43.C). 2. Set the FWD/REV switch to the REV position. 3. Clean the rolls using a moderate amount of 80% isopropyl alcohol on a cotton terry cloth. CAUTION Use the minimum amount of pressure necessary to clean the rolls. You can destroy the silicone layer on the rolls by pressing to hard or scrubbing too long in one spot. WARNING Exercise care when cleaning the rolls with 80% isopropyl alcohol: · Use only in a well ventilated area. · Wear rubber gloves. · Use only on cool rolls. Cleaning heated rolls can ignite the fumes. CAUTION Use only 80% isopropyl alcohol or a rubber cement eraser to clean the laminating rolls. Harsh chemicals like toluene, acetone or MEK destroy the silicone covering of the rolls. To clean the cabinet and covers: WARNING Remove and lockout power from the laminator while you are performing this procedure. You could be severely shocked, electrocuted, or get your fingers caught in the drive mechanisms. 1. Using a damp cotton terry cloth (water only), clean the exterior of the laminator. WARNING Do not use liquid or aerosol cleaners on the laminator. Do not spill liquid of any kind on the laminator. You can be severely shocked, electrocuted or cause a fire. Use only a damp cloth for cleaning. 4. With the laminator rolls no hotter than 110.F, remove dust and dirt from the silicone laminating rolls by running an adhesive-coated board through the laminator. Be sure to set the nip for the thickness of the board used. 5. Allow the laminator to cool. © GBC Pro-Tech 1999 April F-60+ Operation and Maintenance Manual Maintenance and Troubleshooting $GMXVWLQ. WK. 1L. The gap between two rolls is called the nip. The purpose of adjusting the nip is to ensure continuous contact between the rolls as the media is drawn through the machine. This procedure must be done regularly for the main rolls. It is not necessary to set the nip on the pull rolls. Lift Assembly Bolt Properly Set Nip Jam (Distance Between Nut Rolls is Equal) Figure 4-2: Nip Setting Assembly Figure 4-1: Properly Set Nip 4. Adjust the nip so that there is an even line of light across the width of the rolls. Tools required: 5. Secure the jam nut on the lift assembly bolt. • 1/8" hex wrench 6. Replace the cabinet cover. • ." hex wrench To adjust the main roll nip: CAUTION The main roll must be at room temperature to achieve a proper nip setting. 1. Remove the left side cabinet cover with the 1/8" hex wrench by removing the seven screws holding the cover in place. Gently rotate the cover around the clutch knob to allow access to the roll lift system. 2. Lower the upper main roll so that there is a small visible gap between it and the lower main roll. 3. Loosen the ." jam nut securing the lift assembly bolt. Adjust the nip by rotating the lift assembly bolt clockwise to raise the end being adjusted and counterclockwise to lower it. © GBC Pro-Tech 1999 April DownwardForce TightensChain1/4" to 1/2" Play 1/4" to1/2" PlayDownward Force Tightens Chain 1/4" to 1/2" Play DownwardForce TightensChain1/4" to 1/2" Play 1/4" to1/2" PlayDownward Force Tightens Chain 1/4" to 1/2" Play Maintenance and Troubleshooting F-60+ Operation and Maintenance Manual &KDL. 7HQVLRQLQ. Smaller chain tensioning adjustments on the F-60+ Laminator are handled by a secondary chain tensioner, however, when installing a new chain or when the chain tension is more seriously out of adjustment, use the following procedure to adjust the chain tension. Tools required: • 1/8" hex wrench • 7/32" hex wrench • 3/16" hex wrench • Screwdriver To adjust the chain tension: Loosen Motor Mount Bolts WARNING Remove and lockout power from the laminator while you are performing this procedure. You could be severely shocked, electrocuted, or get Figure 4-3: Adjusting the Chain Tension your fingers caught in the drive mechanisms. 5. Using a screwdriver, apply a small amount of downward pressure on the motor by prying against 1. Remove the drive side cabinet cover using the 1/8" the inside of the side frame until there is ." to ." hex wrench by removing the seven screws holding play in the chain. the cover in place. 6. Tighten the mounting bolts while maintaining the downward pressure on the motor. 2. Using a 7/32" hex wrench, remove the pull roll height adjust crank from the drive side of the 7. Engage the top rewind chain tensioner and apply machine. pressure until its chain exhibits similar tension to the primary chain tension. 3. Loosen the top rewind chain tensioner. 8. Engage the bottom rewind chain tensioner and 4. Loosen all four motor mount bolts using the 3/16" apply pressure until its chain exhibits similar ten- hex wrench as shown in the figure below. The sion to the primary chain tension. motor should just move freely within the slots. 9. Replace the cabinet cover. 10. Replace the pull roll height adjust crank. 11. Reapply power to the laminator. © GBC Pro-Tech 1999 April F-60+ Operation and Maintenance Manual Maintenance a...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: